Category Archives: Manual

Siemens Simodrive 611 Error and Fault Code List

Alarm Codes, Manual, Siemens, Simodrive, , ,

MRO Stock carries a large number of Siemens Simodrives. For more information or to request a quote, please call 800-691-8511 or email sales@mrostock.com.

Simodrive 611
Simodrive 611
Simodrive 611 Fault Codes that occur without a number being displayed:

Fault: After power–on, the operating display is inactive
Cause:
— At least 2 phases are missing (NE module)
— At least 2 input fuses have ruptured (NE module)
— Defective electronics power supply in the NE module
— Equipment bus connection (ribbon cable) from the NE module to the ”SIMODRIVE 611 universal” control board is either not inserted or defective
— Defective control board

Fault:  After the controller enable, the motor is stationary at nset ≠ 0
Cause:
— P1401:8 is set to zero
— Power-on inhibit is present for PROFIBUS operation Remove the power-on inhibit with A ”high — low — high” signal change at 65.x or the control bit STW1.0 (ON/OFF 1) or set bit 12 of parameter 1012 to zero

Fault: After the controller has been enabled, the motor briefly moves
Cause:
— Defective power module

Fault: After the controller has been enabled, the motor rotates at max. 50 RPM at nset > 50 RPM or the motor oscillates at nset < 50 RPM
Cause:
— Motor phase sequence is incorrect (interchange 2 phase connections)
— The entered encoder pulse number was too high

Fault: After the controller is enabled, the motor accelerates
to a high speed
Cause:
— Encoder pulse number too small
— Open–loop torque controlled mode selection

Fault: ”– — — — — –” is output on the display unit
Cause:
— There is no drive firmware in this memory module.
— Remedy, refer to fault 001

 

Simodrive 611 Error Code List with Fault/Warning Numbers

Reader’s note

  • In some instances, the space retainers (e.g. \%u) are specified for the texts of the individual faults and warnings. In online operation with SimoCom U instead of a space retainer, an appropriate value is displayed.

 

  • The complete list is updated corresponding to the Edition of this documentation (refer to the Edition in the header lines) and corresponds to the software release of ”SIMODRIVE 611 universal” documented here. The individual faults/warnings are not coded dependent on the software release.
000 Alarm diagnostics not possible
Cause — Communications to the drive have been interrupted.
— Different versions of the ”SimoCom U” start-up and
parameterizing tool and the drive.
Remedy — Check the communications to the drive (cable, interfaces, … )
— The V_611U<Version>.acc file on the hard disk of the PG/PC
should be adapted to the drive as follows:
— Exit ”SimoCom U”
— Delete the V_611U<Version>.acc file (search and delete the file)
— Restart ”SimoCom U” and go online
The V_611U<Version>.acc file is now re-generated and is
harmonized to the drive version.
Never delete the file V000000.acc!
001 The drive does not have firmware
Cause No drive firmware on the memory module.
Remedy — Load the drive firmware via SimoCom U
— Insert the memory module with firmware
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

002 Computation time overflow. Suppl. info: \%X
Cause The computation time of the drive processor is no longer sufficient for
the selected functions in the specified cycle times.
Supplementary information: only for siemens-internal error diagnostics
Remedy Disable functions which take up a lot of computation time, e.g.:
— Variable signaling function (P1620)
— Trace function
— Start-up with FFT or analyzing the step response
— Speed feedforward control (P0203)
— Min/Max memory (P1650.0)
— DAC output (max. 1 channel)
Increase cycle times:
— Current controller cycle (P1000)
— Speed controller cycle (P1001)
— Position controller cycle (P1009)
— Interpolation cycle (P1010)
Acknowledgement POWER ON
Stop response STOP VIII
003 NMI due to watchdog. Suppl. info: \%X
Cause The watchdog timer on the control module has expired. The cause is a
hardware fault in the time basis on the control module.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Replace control module
Acknowledgement POWER ON
Stop response STOP VIII
004 Stack overflow. Suppl. info: \%X
Cause The limits of the internal processor hardware stack or the software
stack in the data memory have been violated. The cause is probably a
hardware fault on the control module.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Power down / power up drive module
— Replace control module
Acknowledgement POWER ON
Stop response STOP VIII
005 Illegal Opcode, Trace, SWI, NMI (DSP). Suppl. info: \%X
Cause The processor has detected an illegal command in the program
memory.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Replace control module
Acknowledgement POWER ON
Stop response STOP VIII

 

 

006 Checksum test error. Suppl. info: \%X
Cause During the continuous check of the checksum in the program / data
memory, a difference was identified between the reference and actual
checksum. The cause is probably a hardware fault on the control mod-
ule.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Replace control module
Acknowledgement POWER ON
Stop response STOP VIII
007 Error when initializing. Supplementary info: \%X
Cause An error occurred when loading the firmware from the memory module.
Cause: Data transfer error, FEPROM memory cell defective
Supplementary information: only for siemens-internal error diagnostics
Remedy Carry-out RESET or POWER-ON.
If a download is still unsuccessful after several attempts, the memory
module must be replaced. If this is unsuccessful the control module is
defective and must be replaced.
Acknowledgement POWER ON
Stop response STOP VIII
020 NMI due to cycle failure
Cause Basic cycle has failed.
Possible causes: EMC faults, hardware fault, control module
Remedy — Check the plug-in connections
— Implement noise suppression measures (screening, check ground
connections)
— Replace control module
Acknowledgement POWER ON
Stop response STOP VIII
025 SSI interrupt
Cause An illegal processor interrupt has occurred. An EMC fault or a hardware
fault on the control module could be the reason.
Remedy — Check the plug- in connections
— Replace control module
Acknowledgement POWER ON
Stop response STOP VIII

 

 

026 SCI interrupt
Cause An illegal processor interrupt has occurred. An EMC fault or a hardware
fault on the control module could be the reason.
Remedy — Check the plug- in connections
— Replace control module
Acknowledgement POWER ON
Stop response STOP VIII
027 HOST interrupt
Cause An illegal processor interrupt has occurred. An EMC fault or a hardware
fault on the control module could be the reason.
Remedy — Check the plug- in connections
— Replace control module
Acknowledgement POWER ON
Stop response STOP VIII
028 Actual current sensing during power-up
Cause When the current actual value sensing runs up, or in cyclic operation at
pulse inhibit, a 0 current is expected. The drive system then identifies
that no currents are flowing (excessive deviation to the theoretical cen-
ter frequency) . It is possible that the hardware for the current actual
value sensing is defective.
Remedy — Check the plug-in connections
— Check whether the control module is correctly inserted
— Replace control module
— Replace the power section
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
029 Incorrect measuring circuit evaluation. Suppl. info:
\%X
Cause The motor measuring system has a motor encoder with voltage output
which requires a measured circuit evaluation with voltage input, or a
resolver with appropriate evaluation. Another measuring circuit evalua-
tion was identified.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Check the plug-in connections
— Implement noise suppression measures (screening, check ground
connections, … )
— Control module and encoder must be the same type
(sin/cos or resolver)
— Replace control module
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

030 S7 communication error. Supplementary info: \%X
Cause A fatal communication error was identified, or the drive software is no
longer consistent. The cause is erroneous communications or a hard-
ware fault on the control module.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Implement noise suppression measures (screening, check ground
connections, …)
— Replace control module
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
031 Internal data error. Suppl. info: \%X
Cause Error in the internal data, e.g. errors in the element / block lists (incor-
rect formats, …). The drive software is no longer consistant. The cause
is propably a hardware fault on the control module.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Re-load drive software
— Replace control module
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
032 Incorrect number of current setpoint filters
Cause An illegal number of current setpoint filters was entered (> 4) (maxi-
mum number = 4).
Remedy Correct number of current setpoint filters (P1200).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
033 Incorrect number of speed setpoint filters
Cause An inadmissible number of speed setpoint filters (> 2) was entered
(max. number = 2).
Remedy Correct number of speed setpoint filters (P1500)
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
034 Axis count function has failed
Cause The function for determining the number of axes that physically exist on
the power section has calculated an illegal value.
Remedy Check that the control module is correctly inserted in the power section
or whether the power section is defective.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

035 Error when saving the user data. Supplementary info:
\%X
Cause An error occurred when saving the user data in the FEPROM on the
memory module.
Cause: Data transfer error, FEPROM memory cell defective
Note: The user data which was last saved, is still available as long as a
new data backup was unsuccessful.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Re-initiate data save.
If unsuccessful after several back-up attempts, then the memory must
be formatted via the menu Options-service-FEPROM.
The memory module must be replaced if this is also unsuccessful.
If the user data valid when the fault occurred are to be re-used with the
new and/or formatted memory module, then these must first be read-
out using SimoCom U.
— Carry-out RESET or POWER ON.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
036 Error when downloading the firmware. Suppl. info: \%X
Cause A error occurred when downloading a new firmware release.
Cause: Data transfer error, FEPROM memory cell defective
Note: As the previously used firmware was erased when downloading,
the drive expects a new firmware download after RESET or POWER
ON.
Supplementary information: only for siemens-internal error diagnostics
Remedy Carry-out RESET or POWER-ON.
The memory module must be replaced if unsuccessful after several
download attempts. If this is also unsuccessful, then the control module
is defective and must be replaced.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
037 Error when initializing the user data. Supplementary
info: \%X
Cause An error occurred when loading the user data from the memory mod-
ule.
Cause: Data transfer error, FEPROM memory cell defective
Supplementary information: only for siemens-internal error diagnostics
Remedy — Execute RESET or POWER ON
— Parameter file ”Load and save in the drive” or re-configure drive
If unsuccessful after several back-up attempts, then the memory must
be formatted via the menu Options-Service-FEPROM.
If this is unsuccessful, the memory module must be replaced. If this is
also unsuccessful, then the control module is defective and must be
replaced.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

039 Error during power section identification. Supplemen-
tary info: \%X
Cause Supplementary information
0x100000:
More than 1 power section (unit) type was identified.
0x200000:
No power section type was identified, although it would have been pos-
sible.
0x30xxxx:
The identified power module differs from the entered PM (P1106). To
xxxx: the code of the identified PM is entered here.
0x400000:
Different power section codes (P1106) are entered for this 2-axis mod-
ule.
Remedy — Execute RESET or POWER ON
— Check whether the control module is correctly inserted in the power
module
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
040 Expected option module is not available.
Cause The parameterization (P0875) expects an option module which is not
available on this control module.
Remedy Compare the type of the expected option module (P0875) with the type
of the inserted option module (P0872) and check/replace the inserted
option module or cancel the option module with P0875 = 0.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
041 The firmware does not support the option module.
Suppl. info: \%u
Cause Supplementary info = 1:
An option module is inserted (P0872) or parameterized (P0875), which
is not supported by the firmware release of the control module.
Remedy Supplementary info = 1:
— Upgrade the firmware
— Use a legal option module
— Cancel the option module with P0875 = 0
Supplementary info = 2:
— Use a permissible option module (DP3)
— Cancel the option module with P0875 = 0
Supplementary info = 3:
— Replace the option module hardware DP1 by option module DP2 or
DP3, without changing the drive parameters and the master
configuring. The parameter for the expected option module remains
at P0875 = 2.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

042 Internal software error. Supplementary info \%u
Cause There is an internal software error.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Execute POWER ON-RESET (press button R)
— Re-load the software into the memory module (execute software
update)
— Contact the Hotline
— Replace control module
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
043 Firmware, option module
Cause The option module does not contain the currently required firmware.
Remedy Use a module with suitable firmware or upgrade the firmware
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
044 Connection to the option module failed. Supplemen-
tary info \%X
Cause The BUS coupling has failed.
Remedy — Execute POWER ON-RESET (press button R)
— Replace option module
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
045 Expected option module is axially unequal
Cause The option module type, expected from the parameterization, is differ-
ent for the two axes of a 2-axis module.
Remedy Set the expected option module type in P0875 the same for both axes,
or cancel for axis B by setting P0875 to 0.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
048 Illegal status PROFIBUS hardware
Cause An illegal status of the PROFIBUS controller was recognized.
Remedy — Execute POWER-ON RESET
— Check the PROFIBUS unit screw connection
— Replace drive module
Acknowledgement POWER ON
Stop response STOP II

 

 

101 Target position block \%n < plus software limit switch
Cause The target position specified in this block lies outside the range limited
by P0316 (plus software limit switch).
Remedy — Change the target position in the block
— Set the software limit switches differently
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
102 Target position block \%n < minus software limit
switch
Cause The target position specified in this block lies outside the range limited
by P0315 (minus software limit switch).
Remedy — Change the target position in the block
— Set the software limit switches differently
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
103 Block number \%n: Direct output function not possible
Cause For the SET_0 or RESET_0 command, an illegal value was entered
into P0086:256 (command parameter).
Remedy Enter value 1, 2 or 3 into P0086:256 (command parameter).
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
104 Block \%n: There is no jump target
Cause A jump is programmed to a non-existent block number in this traversing
block.
Remedy Program the existing block number.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
105 Illegal mode specified in block \%n
Cause Inadmissible information is in P0087:256/P0097 (mode). One position
of P0087:256/P0097 has an illegal value.
For the commands SET_O and RESET_O, the CONTINUE EXTER-
NAL block change enable is not permissible.
For MDI: The configuration of the external block change P0110 is incor-
rect. The external block change is only permissible with P0110 = 2 or 3.
Block change enable only with ”END” or ”CONTINUE EXTERNAL”.
For axis couplings: For COUPLING_IN/COUPLING _OUT via a travers-
ing block (P0410=3, 4 or 8), a block change enable with CONTINUE
FLYING is not possible.
Remedy Check and correct P0087:256/P0097.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI

 

 

106 Block \%n: ABS_POS mode not possible for linear axis
Cause For a linear axes, the positioning mode ABS_POS was programmed
(only for rotary axes).
Remedy Change P0087:256/P0097 (mode).
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
107 Block \%n: ABS_NEG mode not possible for a linear
axis
Cause For a linear axes, the positioning mode ABS_NEG was programmed
(only for rotary axes).
Remedy Change P0087:256/P0097 (mode).
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
108 Block number \%n available twice
Cause There are several traversing blocks with the same block number in the
program memory. The block numbers must be unique over all travers-
ing blocks.
Remedy Assign unique block numbers.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
109 External block change not requested in block \%n
Cause For a traversing block with the block change enable CONTINUE EX-
TERNAL and P0110 (configuration, external block change) = 0, the ex-
ternal block change was not requested.
Remedy Remove the cause that the signal edge is missing at the input terminal
or for a PROFIBUS control signal STW1.13 or for the appropriate field-
bus signal.
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
110 Selected block number \%n does not exist
Cause A block number was selected which is not available in the program
memory or has been suppressed.
Remedy Select the existing block number.
Program the traversing block with the selected block number.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI

 

 

111 GOTO in block number \%n not permissible
Cause The step command GOTO may not be programmed for this block num-
ber.
Remedy Program another command.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
112 Activate traversing task and start referencing, hand-
wheel simultaneously
Cause A positive signal edge was simultaneously detected for the input sig-
nals ”Activate traversing task” and ”Start referencing” and ”Activate
handwheel”.
At power-on or POWER-ON RESET, if both input signals have a ”1”
signal, then for both signals a 0/1 edge (positive edge) is simulta-
neously identified.
Remedy Reset both input signals, and re-start the required function after the
fault has been acknowledged.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
113 Activate traversing task and jog, handwheel simulta-
neously
Cause A positive signal edge was simultaneously detected for the input sig-
nals ”Activate traversing task” and ”Jog 1”, ”Jog 2” and ”Activate hand-
wheel”.
At power-on or POWER-ON RESET, if both input signals have a ”1”
signal, then for both signals a 0/1 edge (positive edge) is simulta-
neously identified.
Remedy Reset both input signals, and re-start the required function after the
fault has been acknowledged.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
114 Block change enable END in block number \%n ex-
pected
Cause The traversing block with the highest block number does not have END
as block step enable.
Remedy — Program this traversing block with block step enable END.
— Program the GOTO command for this traversing block.
— Program additional traversing blocks with higher block number and
program the block step enable END (highest block number) in the
last block.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI

 

 

115 Traversing range start reached
Cause The axis has moved to the traversing range limit in a block with the
command ENDLOS_NEG (–200 000 000 MSR).
Remedy — Acknowledge fault
— Move away in the positive direction (e.g. jog)
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
116 Traversing range end reached
Cause The axis has moved to the traversing range limit in a block with the
command ENDLOS_POS (200 000 000 MSR).
Remedy — Acknowledge fault
— Move away in the negative direction (e.g. jog)
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
117 Target position block \%n < start of the traversing
range
Cause The target position specified in this block lies outside the absolute tra-
versing range (–200 000 000 MSR).
Remedy Change the target position in the block
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
118 Target position block \%n < end of the traversing range
Cause The target position specified in this block lies outside the absolute tra-
versing range (200 000 000 MSR).
Remedy Change the target position in the block
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
119 PLUS software limit switch actuated
Cause For a block with the ENDLOS_POS command, the axis has actuated
the plus software limit switch (P0316) for absolute or relative position-
ing.
The behavior for software limit switch reached, can be set using
P0118.0.
Remedy — Acknowledge fault
— Move away in the negative direction, jog mode
Acknowledgement RESET FAULT MEMORY
Stop response STOP V

 

 

120 MINUS software limit switch actuated
Cause For a block with the ENDLOS_NEG command, the axis has actuated
the minus software limit switch (P0315) for absolute or relative position-
ing
The behavior for software limit switch reached, can be set using
P0118.0.
Remedy — Acknowledge fault
— Move away in the positive direction, jog mode
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
121 Jog 1, jog 2 or handwheel simultaneously active
Cause The input signals ”jog 1”, ”jog 2” or ”activate handwheel” were simulta-
neously activated.
Remedy — Reset both input signals
— Acknowledge the fault
— Activate the required input signal
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
122 Parameter \%u: value range limits violated
Cause The value range limit of the parameter was violated when the dimen-
sion system was changed over from inches to millimeters.
Remedy Place the parameter value within the value range.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
123 Linear encoder for the selected dimension system ille-
gal
Cause For a linear encoder, the dimension system was set to degrees.
Remedy Change the dimension system setting (P0100).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
124 Referencing and jog simultaneously started
Cause For the ”start referencing” and ”Jog 1” and ”Jog 2” input signals, a posi-
tive edge was simultaneously identified.
Remedy Reset both input signals, and re-start the required function after the
fault has been acknowledged.
Acknowledgement RESET FAULT MEMORY
Stop response STOP V

 

 

125 Falling edge of the reference cam not identified
Cause When moving away from the reference cams, the traversing range limit
was reached, as the 1/0 edge of the reference cam was not identified.
Remedy Check the ”reference cam” input signal and repeat the reference point
approach.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
126 Block \%n: ABS_POS for rotary axis, is not possible
without modulo conversion
Cause The ABS_POS positioning mode is only permitted for a rotary axis with
activated module conversion (P0241 = 1).
Remedy Use the valid positioning mode for this axis type.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
127 Block \%n: ABS_NEG for rotary axis is not possible
without modulo conversion
Cause The ABS_NEG positioning mode is only permitted for a rotary axis with
activated modulo conversion (P0241 = 1).
Remedy Use the valid positioning mode for this axis type.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
128 Block \%n: Target position lies outside the modulo
range
Cause The programmed target position (P0081:256/P0091) lies outside the
set modulo range (P0242).
Remedy Program valid target position.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
129 Maximum velocity for a rotary axis with modulo con-
version too high
Cause The programmed maximum velocity (P0102) is too high to correctly
calculate the modulo offset. The maximum velocity may only be so
high, that 90% of the modulo range (P0242) can be traveled through
within one interpolation cycle (P1010).
Remedy Reduce maximum velocity (P0102).
Acknowledgement RESET FAULT MEMORY
Stop response STOP V

 

 

130 Controller or pulse enable withdrawn in motion
Cause Possible causes are:
— One of the following enable signals was withdrawn while moving:
Terminals 48, 63, 64, 663, 65.x, PROFIBUS or bus enable signals,
PC enable from SimoCom U
— Another fault has occurred, which causes the controller or pulse
enable to be withdrawn
— The drive is in the power-on inhibit state
Remedy — Set the enable signals or check the cause of the first fault which
occurred and remove
— Remove the power-on inhibit with the edge (0 —-> 1) at control word
STW1.0 or terminal 65.
— Withdraw the power-on inhibit from the fieldbus signal.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
131 Following error too high
Cause Possible causes are:
— The torque or acceleration capability of the drive is exceeded
— Position measuring system fault
— The position control sense is not correct (P0231)
— Mechanical system blocked
— Excessive traversing velocity or excessive position setpoint
differences
Remedy Check the above causes and remove.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
132 Drive located after the minus software limit switch
Cause The axis was moved to the minus software limit switch (P0315), jog
mode.
The fault can also occur if the software limit switches are inactive if the
position actual value falls below the limit value of –200 000 000 MSR,
that corresponds to 555 revolutions for a rotary axis.
Remedy Return the drive into the traversing range using jog button 1 or 2. Then
acknowledge the fault.
Acknowledgement RESET FAULT MEMORY
Stop response STOP III

 

 

133 Drive located after the plus software limit switch
Cause The axis was moved to the plus software limit switch (P0316), jog
mode.
The fault can also occur if the software limit switches are inactive if the
position actual value exceeds the limit value of 200 000 000 MSR, that
corresponds to 555 revolutions for a rotary axis.
Remedy Return the drive into the traversing range using jog button 1 or 2. Then
acknowledge the fault.
Acknowledgement RESET FAULT MEMORY
Stop response STOP III
134 Positioning monitoring has responded
Cause The drive has not yet reached the positioning window (P0321) after the
positioning monitoring time (P0320) has expired.
Possible causes:
— Positioning monitoring time (P0320) parameters too low
— Positioning window (P0321) parameters too low
— Position loop gain (P0200) too low
— Position loop gain (P0200) too high (instability/tendency to oscillate)
— Mechanical block
Remedy Check above parameters and correct.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
135 Standstill monitoring has responded
Cause The drive has left the standstill window (P0326) after the standstill mon-
itoring time (P0325) has expired.
Possible causes are:
— Position actual value inversion (P0231) incorrectly set
— Standstill monitoring time (P0325) parameters too low
— Standstill window (P0326) parameters too low
— Position loop gain (P0200) too low
— Position loop gain (P0200) too high (instability/tendency to oscillate)
— Mechanical overload
— Check connecting cable motor/converter (phase missing, exchanged)
Remedy Check above parameters and correct.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II

 

 

136 Conv.factor,feedforward contr.speed,parameter set
\%d,cannot be represented
Cause The conversion factor in the position controller between velocity and
speed cannot be displayed.
This factor depends on the following parameters:
— Spindle pitch (P0236), for linear axes
— Gearbox ratio (P0238:8 / P0237:8).
Remedy Check the above mentioned parameters and correct.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
137 Conv.factor,pos.contr.output,parameter set \%d,cannot
be represented
Cause The conversion factor in the position controller between the following
error and the speed setpoint cannot be represented.
This factor depends on the following parameters:
— Spindle pitch (P0236) (for linear axes)
— Gearbox ratio P0238:8 / P0237:8
— Position control loop gain P0200:8
Remedy Check the above mentioned parameters and correct.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
138 Conversion factor between the motor and load too
high
Cause The conversion factor between the motor and load is greater than 2 to
the power of 24 or less than 2 to the power of –24.
Remedy Check the following parameters and correct:
P0236, P0237, P0238, P1005, P1024
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
139 Modulo range and ratio do not match
Cause For EnDat absolute value encoders or for distance-coded measuring
systems the ratio between the encoder and load must be so that the
full range of the encoder is a multiple of the modulo range.
The following condition must be fulfilled (for single turn or for distance-
coded encoder 1 instead of P1021/P1031):
IM: P1021 * P0238:8 / P0237:8 * 360 / P0242 must be an integer num-
ber.
DM: P1031 * 360 / P0242 must be an integer number
Remedy — Check and correctP1021, P0238:8, P0237:8
— Adapt the modulo range (P0242)
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

140 Minus hardware limit switch
Cause A 1/0 edge was identified at the ”Minus hardware limit switch” input sig-
nal.
Remedy Return the drive into the traversing range using jog button 1 or 2. Then
acknowledge the fault.
Acknowledgement RESET FAULT MEMORY
Stop response STOP III
141 Plus hardware limit switch
Cause A 1/0 edge was identified at the ”Plus hardware limit switch” input sig-
nal.
Remedy Return the drive into the traversing range using jog button 1 or 2. Then
acknowledge the fault.
Acknowledgement RESET FAULT MEMORY
Stop response STOP III
142 Input I0.x not parameterized as equivalent zero mark
Cause When entering an external signal as equivalent zero mark (P0174 = 2),
input I0.x must be assigned ”equivalent zero mark” function (Fct.
No.:79).
if a direct measuring system is used, input I0.B must be assigned the
”equivalent zero mark” function (Fct. No.: 79).
Remedy — Motor measuring system: P0660 = 79
— Direct measuring system: P0672 = 79
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
143 Endless traversing and external block change in block
\%n
Cause The block change enable CONTINUE_EXTERNAL for the
ENDLESS_POS or ENDLESS_NEG command is only permitted with
P0110 = 0 or 1.
Remedy Block change enable or change P0110.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
144 Switching-in/switching-out MDI erroneous
Cause In the active traversing program, MDI was switched-in or, in the active
MDI block, MDI was switched-out.
Remedy Acknowledge fault
Change P0110
Acknowledgement RESET FAULT MEMORY
Stop response STOP II

 

 

145 Fixed endstop not reached
Cause In a traversing block with the FIXED ENDSTOP command, the fixed
endstop was not reached. The fixed endstop lies outside the position
programmed in this block.
After interrupting the function, traverse to fixed stop, the drive was
pushed out of its position (drop position).
Remedy Check programming
Increase kP0326 if the drive was forced out of the position.
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
146 Fixed endstop, axis outside the monitoring window
Cause In the ”Fixed endstop reached” status, the axis has moved outside the
defined monitoring window.
Remedy — Check P0116:8 (fixed endstop, monitoring window)
— Check mechanical system
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
147 Enable signals withdrawn at the fixed endstop
Cause Possible causes are:
— One of the following enable signals was withdrawn while traversing to
the fixed endstop: Terminals 48, 63, 64, 663, 65.x, PROFIBUS and bus
enable signals, PC enable from SimoCom U
— Another fault has occurred, which causes the controller or pulse
enable to be withdrawn
Remedy Set the enable signals and check the cause of the first fault and re-
move.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
148 Velocity in block \%n outside the range
Cause The velocity specified in this block lies outside the range (6 to 2 000
000 000 c*MSR/min).
Remedy Change the velocity in the block
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI

 

 

149 Incorrect data for modulo axis with absolute encoder.
Supplementary info \%u
Cause Data error for modulo drive with absolute encoder and any gear factor.
— Data was not able to be saved after power-on.
— Absolute position was not able to be read- out of the encoder.
— P1021 * P0238:8 / P0237:8 * 360 / P0242 must be greater than or
equal to 1.
— Modulo range must be n * 360 Degrees with n = 1, 2, ….
— Drive booting was interrupted.
— When parameter set > 0 is selected the ratios P0238:8 / P0237:8 are
not equal.
Supplementary information: only for siemens-internal error diagnostics
Remedy — Adjust the drive by setting the absolute value.
— Check the switching threshold in P1162 (minimum DC link voltage).
— Check the hysteresis of the DC link voltage monitoring in P1164.
— Check parameters P0237:8, P0238:8, P0242.
— Check that the DC link voltage is deactivated (P1161 = 0).
— Wait until ”run” appears in the seven-segment display before booting.
— Check that the activation threshold is less than the DC link voltage
(P1162 + P1164 < P1701).
Acknowledgement POWER ON
Stop response STOP V
150 External position reference value < max. traversing
range suppl. info \%u
Cause The external position reference value has exceeded the upper travers-
ing range limit.
Supplementary info = 0:
Limit exceeded after the coupling factors P0401/P0402 identified, i.e.
P0032 > 200 000 000 MSR.
Supplementary info = 1:
Limit exceeded after the coupling factors P0401/P0402 identified, i.e.
P0032 * P0402 / P0401 > 200 000 000 MSR.
Remedy Return the external position reference value to the value range. Then
acknowledge the fault.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II

 

 

151 External position reference value < min. traversing
range suppl. info \%u
Cause The external position reference value has fallen below the lower tra-
versing range limit.
Supplementary info = 0:
Limit fallen below after the coupling factors P0401/P0402 identified, i.e.
P0032 < — 200 000 000 MSR.
Supplementary info = 1:
Limit fallen below after the coupling factors P0401/P0402 identified, i.e.
P0032 * P0402 / P0401 < — 200 000 000 MSR.
Remedy Return the external position reference value to the value range. Then
acknowledge the fault.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
152 Pos.ref.val. and act.val. output via the bus interf. lim-
ited. Suppl. info \%X
Cause The output of the position reference value, position actual value or
position correction value is parameterized via PROFIBUS or the bus
interface. However, the value to be output can no longer be repre-
sented in 32 bits and was therefore limited to the maximum values
0x7fffffff or 0x80000000.
The traversing range which can be displayed is given by
Lower limit: — 2147483648 * P896 / P884
Upper limit: + 2147483647 * P896 / P884
The supplementary information explains which process data has vio-
lated the lower or upper limit:
Supplementary info process data Violation
xx1Position reference value Xset (No. 50208) Upper limit exceeded
xx2Position reference value Xset (No. 50208) Lower limit fallen below
x1x Position actual value Xact (No. 50206) Upper limit exceeded
x2x Position actual value Xact (No. 50206) Lower limit fallen below
1xx Position correction value dxKorr (No. 50210) upper limit exceeded
2xx Position correction value dxKorr (No. 50210) lower limit fallen be-
low
Remedy — Move drive back e.g. by jogging in the representable traversing
range.
— Adapt the lower and upper limit to the required traversing range using
P884 and P896.
Acknowledgement RESET FAULT MEMORY
Stop response STOP III

 

 

160 Reference cam not reached
Cause After starting the reference point approach, the axis moves through the
distance in P0170 (max. distance to the reference cam) without finding
the reference cam.
Remedy — Check the ”reference cam” signal
— Check P0170
— If it is an axis without reference cam, then set P0173 to 1
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
161 Reference cams too short
Cause When the axis moves to the reference cam, and does not come to a
standstill at the cam, then this error is signaled, i.e. the reference cam
is too short.
Remedy — Set P0163 (reference point approach velocity) to a lower value
— Increase P0104 (maximum deceleration)
— Use larger reference cam
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
162 No zero reference pulse present
Cause — After the reference cam has been left, the axis has moved through
the distance in P0171 (max. distance between the reference cam/zero
pulse), without finding a zero pulse.
— For distance-coded measuring system (from SW 8.3 onwards):
The maximum permissible distance (clearance) between two reference
marks was exceeded.
Remedy — Check the encoder with reference to the zero mark
— Set P0171 to a higher value
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
163 Encoderless operation and operating mode do not
match
Cause Encoderless operation was parameterized (P1006) and the ”Position-
ing” mode selected.
Remedy Set operating mode ”speed/torque setpoint” (P0700 = 1)
Acknowledgement POWER ON
Stop response STOP V
164 Coupling released during the traversing job.
Cause The coupling was disconnected while a traversing task was running
Remedy First exist the traversing task and then disconnect the coupling.
Acknowledgement RESET FAULT MEMORY
Stop response STOP III

 

 

165 Absolute positioning block not possible
Cause Traversing blocks with absolute position data are not permitted while
the axis coupling is activated.
Remedy Correct traversing block
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
166 Coupling not possible
Cause — No coupling can be established in the actual operating status.
— For P0891=2 or 3, it is not possible to couple using the input signal
”Activate coupling through I0.x” (fast input).
Remedy — Check the coupling configuration (P0410)
— Set angular encoder interface (P0890, P0891)
— Check the source of the external position reference value and input
signal source.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI
167 Activate coupling signal present
Cause — The input signal ”Activate coupling” is present. An edge of the input
signal is necessary to activate the coupling.
— In the jog mode, while traversing, the input signal ”coupling on” was
entered.
— The ”coupling in” input signal was entered in handwheel operation.
Remedy Reset ”Activate coupling” input signal
Acknowledge fault
Set the input signal again to switch-in the coupling
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
168 Overflow, buffer memory
Cause Occurs for couplings with queue functionality.
A maximum of 16 positions can be saved in P0425:16.
Remedy Ensure that maximum 16 positions are saved.
Acknowledgement POWER ON
Stop response STOP IV

 

 

169 Coupling trigger missed
Cause Occurs for couplings with queue functionality.
Synchronizatin is requested using the KOPPLUNG_ON command and
it is identified that the position at which the coupling is switched-in, has
already bee passed.
Remedy Ensure that the slave drive was stationary for at least 1 IPO clock cycle
(P1010), before the coupling for the next element in the position
memory must be switched-in.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
170 Coupling switched-out during the traversing program
Cause While the drive was executing a traversing program, the ”Activate cou-
pling” input signal was reset.
Remedy Only switch-out the coupling if the traversing program has been com-
pleted.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
171 Coupling not possible
Cause While the drive was executing a traversing program, the ”Active cou-
pling” input signal was set.
Remedy Only switch-in the coupling if the traversing program has been com-
pleted.
Acknowledgement RESET FAULT MEMORY
Stop response STOP V
172 External block change for coupling not possible
Cause If there is an existing coupling, traversing blocks with external block
enable are only permitted if P0110 = 2.
Remedy Correct traversing program
Change P0110 (configuration, external block change)
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
173 Coupling and traverse to endstop simultaneously
Cause Not possible to simultaneously couple and traverse to the endstop.
Remedy Correct traversing program
Acknowledgement RESET FAULT MEMORY
Stop response STOP V

 

 

174 Passive referencing not possible
Cause For the passive referencing, the encoder interface must be switched as
input and the ”Positioning” mode must be set.
Remedy — Set the ”Positioning” mode (P0700)
— Set angular encoder interface (P0890, P0891)
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
175 Passive referencing not realized. Supplementary info:
\%u
Cause While the master drive corrects the zero mark offset, the slave drive
must pass over a zero mark.
Supplementary information
0 = reference cam not found
1 = Reference cam not left
2 = Zero reference pulse not found
Remedy Ensure that the cam of the slave drive is located between the cam and
the reference point of the master drive. Appropriately shift the cam
and/or increase the reference point offset (P0162) at the master drive.
If the zero pulse is not found, the reference point offset (P0162) must
also be increased at the master drive.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
176 Absolute encoder must be adjusted
Cause Passive referencing with absolute encoders (e.g. EnDat encoders) is
only possible after the encoder has been adjusted.
Remedy Adjust the drive by setting the absolute value.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV

 

 

177 Start-up passive referencing P179 not possible
Cause The start-up help for passive referencing determines the reference
point offset in P0162 in the slave drive. The following prerequisites
must be available:
— (permanent) position coupling exists to the master drive
— Master drive must be precisely at its reference point
— Slave drive has passed the zero mark.
Remedy — Establish a coupling at the slave drive: PosStw.4 or input terminal
function 72/73
— Reference the master drive: STW1.11 or input terminal function 65 at
the master drive
— ”Wiring” check: The requirement for passive referencing must be
transferred from the master to the slave drive:
Masterdrive: Output via ZSW1.15, QZsw.1 or output terminal
function 69
Slave drive: read-in via STW1.15, QStw.1 or input terminal function 69
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
180 Teach-in without reference point
Cause Teach-in only possible for a referenced axis.
Remedy Request reference axis and teach in
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
181 Teach-in block invalid
Cause The specified teach-in block is invalid.
Remedy Specify the valid and existing traversing block.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
182 Teach-in standard block invalid
Cause The specified teach-in standard block is invalid.
Remedy Specify the valid and existing traversing block.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
183 Teach-in block not found
Cause The specified teach-in block is not found.
Remedy Select the valid and existing traversing block.
Activate ”Automatically search for block numer” function.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV

 

 

184 Teach-in standard block not found
Cause The specified teach-in standard block is not found.
Remedy Generate the required standard block for the specified block number
Enter the correct block number.
Acknowledgement RESET FAULT MEMORY
Stop response STOP IV
185 Positioning mode invalid
Cause For the ”Spindle positioning” function, the positioning mode (P0087) is
not valid.
Remedy Program traversing block positioning as absolute, absolute positive or
absolute negative.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
186 Spindle cannot be referenced, supplementary info \%d
Cause For the ”Spindle positioning” function, an error has occurred while posi-
tioning.
Supplementary info  Significance
0 the distance between the last two zero marks was not correct.
1 For two revolutions a zero mark was no longer detected, which
was in a tolerance bandwidth of P0126.
Remedy Check cable and connections.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II

 

 

187 Conversion factor spindle pos. cannot be represented,
supplementary info \%d
Cause Conversion factors for spindle positioning was not able to be intialized
Supplementary info, ones and tens position:
00: Conversion factor, velocity to speed too small
01: Conversion factor, velocity to speed too high
02: Conversion factor, adaptation filter too low ( –> increase P0210)
03: Conversion factor, adaptation filter too high (–> reduce P0210)
04: Conversion factor, pre-control balancing filter too low
(–> increase P0206)
05: Conversion factor, pre-control balancing filter too high
(–> reduce P0206)
06: Conversion factor, sum delay too small
07: Conversion factor, sum delay too large
08: Conversion factor, following error model too small
09: Conversion factor, following error model too large
The hundreds position of the supplementary info contains the parmeter
set involved.
Remedy Check and correct specified parameters.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
188 Spindle positioning: P\%d illegal
Cause Spindle positioning requires the following parameterization:
P0241 = 1
P0100 = 3
Remedy Correct the specified parameter or cancel spindle positioning by setting
P0125 to 0.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
189 Jogging, incremental invalid
Cause 1. Jogging incremental is not valid in this mode.
2. An attempt was made to move an axis away from a software limit
switch using incremental jogging — however the axis is not at the soft-
ware limit switch, but behind it.
3. An attempt was made while executing one or several traversing
blocks (also via an axis coupling) to activate incremental jogging.
Remedy 1. Commission the drive in the positioning mode.
2. Move back with jog key 1 or 2 with velocity.
3. Interrupt traversing blocks with the operating condition, reject tra-
versing task.
Acknowledgement RESET FAULT MEMORY
Stop response STOP VI

 

 

190 Actual firmware does not support spindle positioning
Cause This firmware does not support the spindle positioning function.
Remedy Set parameter P0125 to 0
Acknowledgement POWER ON
Stop response STOP II
191 Zero mark setting unsuccessful
Cause It is not possible to set the internal zero mark, if
1. Input signal ”Spindle positioning on” is set, or
2. Still no zero mark found.
Remedy Maintain the following sequence:
1. Execute spindle positioning —- > zero mark found
2. Withdraw input signal ”spindle positioning on”
3. Set the internal zero mark (P0127=1).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
192 Max. search velocity too high
Cause The maximum search velocity for spindle positioning is greater than the
maximum motor speed.
Remedy Reduce parameter P0133 or reduce the velocity in the traversing block.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
193 Zero mark not found
Cause The zero mark (encoder or equivalent zero mark, e.g. BERO) was not
found. Gearbox ratio (mechanical system) was not correctly parameter-
ized using parameter P0237/P0238.
Remedy — Check the equivalent zero mark (BERO) function, if required, replace
the BERO
— Readjust the clearance when using BERO
— Check the cabling
— Correctly parameterize the gearbox ratio (mechanical system) using
parameter P0237/P0238
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
194 Spindle positioning is only possible with motor 1
Cause Spindle positioning is only possible with motor 1.
Remedy Activate motor data set 1 before the spindle positioning command.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II

 

 

195 Speed pre-control not permissible
Cause Speed pre-control is not permissible with spindle positioning.
Remedy Cancel the speed pre-control (P0203)
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
196 Illegal combination of input signals (warning \%u)
Cause An illegal combination of signals is present at the inputs, at the Profibus
control words or at the appropriate bus signals. The detailed cause of
the error can be taken from the help text associated with the warning
that is entered as supplementary information.
This fault can be activated or suppressed using Parameter P338.
Supplementary information: Warning number
Remedy Change the input signals or suppress the fault using P338.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
501 Measuring circuit error, absolute current
Cause 1. The smoothed absolute current (P1254, current monitoring time
constant) is greater than 120 % of the permissible power section cur-
rent (P1107).
2. For an active rotor position identification, the permissible current
threshold was exceeded.
3. The P gain of the controller (P1120) has been set too high.
Remedy — Motor/controller data not correct
— For active rotor position identification P1019 (current, rotor position
identification) check and if required reduce
— Reduce the P gain of current controller (P1120), check the current
controller adaptation (P1180, P1181, P1182)
— Replace control module
— Replace the power section
Acknowledgement POWER ON
Stop response parameterizable

 

 

504 Measuring circuit error, motor measuring system
Cause The encoder signal level is too low, faulted (incorrect shielding), or the
cable breakage monitoring function has responded.
After separately shutting down the supply voltage at the drive, for
SIMODRIVE 611 universal HRS with 1Vpp encoder or SIMODRIVE
universalE HRS with 1Vpp encoder, this fault message can be output
during the shutdown procedure without any significance for the control.
Remedy — Use the original Siemens pre-assembled encoder cables
(better screening)
— Check for sporadic interruptions (loose contact, e.g. when the drag
cable is being moved)
— For toothed-wheel encoders, check the clearance between
the toothed wheel and sensor
— Check the encoder, encoder cables and connectors between the
motor and control module
— Check the screen connection at the front panel of the control module
(top screw)
— Replace the encoder cables or the control module
— Exchange the encoder or motor
— If this fault was signaled without any significance, then it should either
be acknowledged in the control or the drive and control should be pow-
ered-down together.
Acknowledgement POWER ON
Stop response parameterizable
505 Meas.circ.error motor meas.syst.abs.track
Cause 1. The motor absolute track (CD track) is monitored for an interrupted
conductor. For optical encoders, the absolute track supports the evalu-
ation of the mechanical position within one motor revolution.
2. For absolute encoders with EnDat interface, this fault displays an
initialization error.
Note:
Additional information on the reason for the fault is included in P1023
(IM diagnostics).
Remedy — Incorrect encoder cable type
— Check for sporadic interruptions (loose contact, e.g. when the drag
cable is being moved)
— Remove noise which is coupled in due to inadequate screening of the
cable by replacing the encoder cable
— Incorrect encoder type configured (e.g. ERN instead of EQN)
— Check the encoder, encoder cables and connectors between the
motor and control module
— Replace control module
— Replace encoder
Acknowledgement POWER ON
Stop response parameterizable

 

 

507 Synchronization error rotor position
Cause The difference between the actual rotor position and the new rotor posi-
tion, which was determined by fine synchronization is greater than 45
degrees electrical.
When commissioning a linear motor with rotor position identification
(e.g. linear motor, 1FE1 motor), the fine synchronization was not ad-
justed.
Remedy — Adjust the fine synchronization using P1017 (commissioning help
function)
— Check encoder cable, encoder cable connection and grounding
(possibly EMC problems)
— Check the shield contact, front panel, control module (upper screw)
— Replace control module
— Exchange the encoder or motor
Acknowledgement POWER ON
Stop response parameterizable
508 Zero mark monitoring, motor measuring system
Cause The measured rotor position fluctuates between 2 encoder zero marks
(encoder lines may have been lost).
Note:
The encoder monitoring function can be disabled using P1600.8.
Remedy — Use the original Siemens pre-assembled encoder cables
(better screening)
— Check for sporadic interruptions (loose contact, e.g. due to cable
drag movements)
— For toothed-wheel encoders, check the clearance between the
toothed wheel and sensor
— Check the encoder, encoder cables and connectors between the
motor and control module
— Check the shield contact, front panel, control module (upper screw)
— Replace the encoder cables or the control module
— Replace control module
— Exchange the encoder or motor
Acknowledgement POWER ON
Stop response parameterizable

 

 

509 Drive converter limiting frequency exceeded
Cause The drive converter has exceeded the maximum permissible drive con-
verter frequency.
Remedy — Encoder pulse number is too low, enter the actual encoder pulse
number in P1005
— Stop the belt slipping in open-loop torque controlled mode
(the belt slips)
— Check P1400 (rated motor speed)
— Check P1146 (maximum motor speed)
— Check P1147 (speed limiting)
— Check P1112 (motor pole pair number)
— Check P1134 (rated motor frequency)
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
510 Positive feedback identified
Cause Ramp-up:
The actual rotor position and the position information read-out of the
encoder were compared with one another while booting and a deviation
of more than 45 Degrees was identified, P1011[10].
Operational:
The acceleration/velocity direction is different than the torque/force di-
rection.
This monitoring function can be set using P1645 and P1646.
Remedy — This alarm can also occur when axes are mechanically blocked.
Check the fault cause analog to Alarm 605 ”Speed controller output
limited”.
— Operation may only be resumed after the fault has been removed
otherwise there is a danger of uncontrollable motion.
Ramp-up:
— The deviation is due to dirt on the encoder or incorrect mounting/
installation of the encoder or encoder cable.
Operational:
— If the load oscillates strongly increase the delay for the monitoring
(P1645).
— Caution : The value in P1645 influences the duration of the axis
motion, triggered by positive feedback until the fault responds.
— Check the encoder: Mounting, dirt, absolute track fault, lost pulses,
encoder cable
Acknowledgement POWER ON
Stop response parameterizable

 

 

511 Ground fault detected
Cause Firmware has detected a ground fault.
Measured phase currents are greater than the response value of the
ground fault test configured in P1167 or the motion is greater than the
maximum permitted motion for the ground fault test configured in
P1168.
Remedy — Ground fault in the power cables or at the motor.
During the ground fault test, at least one phase increases above the
threshold P1167 or P1168.
Detailed information can be taken from the diagnostics parameter
P1169.
Acknowledgement POWER ON
Stop response parameterizable
512 Measuring circuit error, direct measuring system
Cause The encoder signal level is too low, faulted (incorrect shielding), or the
cable breakage monitoring function has responded.
Remedy — Use the original Siemens pre-assembled encoder cables
(better screening)
— Check for sporadic interruptions (loose contact, e.g. due to cable
drag movements)
— For toothed-wheel encoders, check the clearance between the
toothed wheel and sensor
— Check the encoder, encoder cables and connectors between the
encoder and control module
— Check the shield contact, front panel, control module (upper screw)
— Replace the encoder cables or the control module
— Replace encoder
Acknowledgement POWER ON
Stop response parameterizable

 

 

513 Measuring circuit error, direct measuring system abso-
lute track
Cause For absolute encoders with EnDat interface, this fault indicates an init-
ialization error.
Note:
Additional information on the reason for the fault is included in P1033
(DM diagnostics).
Remedy — Incorrect encoder cable type
— Check for sporadic interruptions (loose contact, e.g. when the drag
cable is being moved)
— Remove noise which is coupled in due to inadequate screening of the
cable by replacing the encoder cable
— Incorrect encoder type configured (e.g. ERN instead of EQN)
— Check the encoder, encoder cables and connectors between the
encoder and control module
— Replace control module
— Replace encoder
Acknowledgement POWER ON
Stop response parameterizable
514 Zero mark monitoring, direct measuring system
Cause A fluctuation in the measured values has occurred between 2 encoder
zero marks (encoder pulses may have been lost).
Note:
The encoder monitoring can be disabled using P1600.14.
Remedy — Use the original Siemens pre-assembled encoder cables
(better screening)
— Check for sporadic interruptions (loose contact, e.g. due to cable
drag movements)
— For toothed-wheel encoders, check the clearance between the
toothed wheel and sensor
— Check the encoder, encoder cables and connectors between the
motor and control module
— Check the shield contact, front panel, control module (upper screw)
— Replace the encoder cables or the control module
— Replace encoder
Acknowledgement POWER ON
Stop response parameterizable

 

 

515 Power module temperature, exceeded
Cause The power section temperature is sensed using a temperature sensor
on the heatsink. The drive is immediately shut down 20 seconds after
the heatsink temperature alarm in order to prevent the power section
being thermally destroyed (regenerative stop).
Remedy Improve the drive module cooling, e.g. using:
— Higher airflow in the switching cabinet, possibly cool the ambient air
of the drive modules
— Avoid many acceleration and braking operations which follow
quickly one after the other
— Check that the power section for the axis/spindle is adequate,
otherwise use a higher-rating module
— Ambient temperature too high (refer to the Planning Guide)
— Permissible installation altitude exceeded (refer to the
Planning Guide)
— Pulse frequency too high (refer to the Planning Guide)
— Check fan, if required, replace
— Maintain the minimum clearance above and below the power section
(refer to the Planning Guide)
Acknowledgement POWER ON
Stop response parameterizable
591 Pos.contr.clock cycle not equal to DP clock cycle/mas-
ter applic. clock cycle
Cause For a 2-axis module, one axis is in the n-set mode and one axis in the
positioning mode. For the axis in the n-set mode, a position controller
clock cycle (of the master) is entered via the clock-cycle synchronous
PROFIBUS or the bus interface. This position controller clock cycle
differs from the parameterized position controller clock cycle (P1009) of
the axis in the positioning mode. The position controller clock cycle of
the master is obtained, in the n-set mode, from the DP clock cycle
(Tdp) or the clock cycle of the bus interface multiplied by the time grid
Tmapc.
Remedy For a clock cycle synchronous PROFIBUS (isochronous) or the bus
interface, the clock cycles configured for the bus (parameterization) are
aligned with the position controller clock cycle P1009 from the position-
ing axis and n-set axis.
Acknowledgement POWER ON
Stop response STOP II

 

 

592 Spindle positioning: Pos. contr. not equal to master
application clock cycle
Cause The function ”spindle positioning” requires, for a clock-cycle synchron-
ous PROFIBUS or the bus interface, that the position controller clock
cycle of the master matches the parameterized position controller clock
cycle (P1009). The position controller clock cycle of the master is ob-
tained from the DP clock cycle (Tdp) multiplied by the time grid Tmapc.
Remedy For the clock-cycle synchronous PROFIBUS or the bus interface, the
clock cycles configured for the bus (parameterization) are aligned with
the position controller clock cycle P1009.
Acknowledgement POWER ON
Stop response STOP II
593 Fieldbus: Drive is not in synchronism. Supplementary
info: \%X
Cause Supplementary information
0x01:
The master sign-of-life has more consecutive failures than permitted.
The permissible sign-of-life errors are specified using P0879 bits 2–0
(configuration).
0x02:
The Global Control telegram to synchronize the clock cycles has failed
in operation for several consecutive DP clock cycles or in several DP
clock cycles has violated the time grid specified using the parameteriz-
ing telegram (refer to times Tdp and Tpllw). If the complete DP commu-
nications permanently fails, at the latest after the response monitoring
times specified when configuring the bus, fault 595 is also output.
Remedy — Check whether communications is briefly or continuously interrupted.
— Check whether the BUS master can operate in clock cycle
synchronism and outputs the global control telegrams, necessary for
clock cycle synchronous operation, in the equidistant DP clock cycle.
— Check whether clock synchronism has been activated in the bus con-
figuration, although it is not controlled by the master used.
— Check whether the master sign-of-life is received and incremented in
the parameterized clock cycle.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II

 

 

595 Fieldbus: Cyclic data transfer was interrupted
Cause The cyclic data transfer between the master and slave was interrupted
due to the fact that cyclic frames were missing, or due to the reception
of a parameterizing or configuring frame.
Examples:
— Bus connection interrupted
— Master runs up again
— Master has changed into the ’Clear’ state
For a passive axis, fault cannot be acknowledged using ”RESET
FAULT MEMORY”.
Remedy Check the master and bus connection to the master. As soon as cyclic
data transfer runs again, the fault can be acknowledged.
Set P0875 to 0 in the passive axis.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
596 PROFIBUS: Connection to the publisher \%u inter-
rupted
Cause Cyclic data transfer between this slave and a slave-to-slave commu-
nications publisher was interrupted as cyclic telegrams were missing.
Examples:
— Bus connection interrupted
— Publisher failure
— Master runs up again
— The response monitoring (Watchdog) for this slave was de-activated
via the parameterizing telegram (SetPrm)
(Diagnostics: P1783:1 bit 3 = 0).
Supplementary info: PROFIBUS address of the publisher
Remedy Check the publisher and bus connections to the publisher, to the
master and between the master and publisher. If the watchdog is de-
activated, activate the response monitoring for this slave via Drive ES.
As soon as cyclic data transfer runs again, the fault can be acknowl-
edged.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II

 

 

597                             PROFIBUS: Drive not in synchronism. Supplementary

 

information: \%X

 

Cause                           Supplementary information

 

0x01:

 

The master sign-of-life (STW2, bits 12–15) has more consecutive fail-

 

ures than permitted. The permissible sign-of-life error is specified using

 

P0879 bit 2–0 (PROFIBUS configuration).

 

0x02:

 

The Global Control telegram to synchronize the clock cycles has failed

 

in operation for several DP cycles in a row or has violated the time grid

 

–

 

If the complete DP com-

 

munications fails permanently, then Fault 599 is also output — at the

 

latest after the response monitoring time specified when the bus was

 

configured, expires.

 

Remedy                        — Check whether communications is briefly or continuously interrupted.

 

— Check whether the PROFIBUS master can operate in clock cycle

 

synchronism and the Global Control Telegrams, required for clock

 

cycle synchronous operation, are output in the equidistant DP clock

 

cycle.

 

— Check whether clock synchronism has been activated in the bus

 

configuration, although it is not controlled by the master used.

 

— Check whether the master sign-of-life (STW2, bits 12–15) is received

 

and is incremented in the parameterized clock cycle.

 

Acknowledgement         RESET FAULT MEMORY

 

Stop response              STOP II

 

 

 

598 PROFIBUS: Synchronization error. Supplementary
info: \%X
Cause Supplementary information
0x01:
The expected 1st global control clock cycle display did not occur within
the waiting time.
0x02:
PLL synchronization unsuccessful
0x03:
When synchronizing to the clock cycle, the global control clock cycle
had more consecutive failures than are permitted.
0x06:
The data frames w. the process data (setpoint direction) were only re-
ceived after the time (To–125  s)) in the slave has expired.
Remedy — Check whether the PROFIBUS master can operate in synchronism
with the clock cycle, and that the necessary global-control frames are
output for operation in synchronism with the clock cycle.
— Check whether clock synchronism has been activated in the bus con-
figuration, although it is not controlled by the master used.
— Check whether the equidistant DP clock cycle, transferred with the
parameterizing telegram, was actually set and activated at the master.
— Check whether the time Tdx — defined in the master configuring —
corresponds to the actual data transfer time to all slaves and is less
than the configured time (To–125  s).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II
599 PROFIBUS: Cyclic data transfer was interrupted
Cause The cyclic data transfer between the master and slave was interrupted
due to the fact that cyclic frames were missing, or due to the reception
of a parameterizing or configuring frame.
Examples:
— Bus connection interrupted
— Master runs up again
— Master has changed into the ’Clear’ state
For a passive axis, fault cannot be acknowledged using ”RESET
FAULT MEMORY”.
Remedy Check the master and bus connection to the master. As soon as cyclic
data transfer runs again, the fault can be acknowledged.
Set P0875 to 0 in the passive axis.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II

 

 

600 Pole position (P1016) has not been set
Cause The pole position set (P1016) is 0.
Commissioning using P1017= –1 is only possible if P1016 is not equal
to 0.
Remedy First measure the pole position and enter ( P1016 ), then complete
commissioning ( P1017 = –1 ).
If P1016 should be precisely 0, enter 0.001.
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
601 Error in AD conversion, terminal 56/14 or 24/20
Cause A timing error was identified when reading-out the A/D converter for
terminal 56.x/14.x or 24.x/20.x. The read values are probably incorrect/
faulty.
Remedy Replace closed-loop control module
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
602 Open-loop torque controlled oper. w/o encoder is not
perm.
Cause In the IM mode, open-loop torque controlled operation was selected via
an input terminal or via PROFIBUS-DP or the bus interface.
Remedy Deselect the torque-controlled operation or leave the IM mode (change-
over speed P1465).
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
603 Changeover to non-parameterized motor data set
Cause An attempt was made to change over to a motor data set which was
not parameterized.
Remedy Parameterizing motor data set
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable

 

 

604 Motor encoder is not adjusted
Cause For an EnDat motor measuring system, it was identified that the serial
number does not match that saved, i.e. the encoder has still not run
with this drive.
Remedy 1FN3 linear motors (if P1075=1):
Measure the rotor position offset to the EMF of the U_R phase and add
to P1016 as the commutation angle offset. Then set P1017 to –1 in
order to save the serial number of the EnDat encoder.
otherwise:
To determine commutation angle offset in P1016, initiate the rotor posi-
tion identification routine via P1017=1. The rotor position identification
routine is executed by acknowledging the fault and setting the enable
signals.
Note:
also refer to description of P1017
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
605 Position controller output limited
Cause The speed setpoint requested from the position controller lies above
the max. motor speed.
Possible causes:
— Programmed velocity (P0082:256) too high
— Max. acceleration (P0103) or deceleration (P0104) too high
— Axis is overloaded or blocked
Remedy — Check and correct the above parameter
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
606 Flux controller output limited
Cause The specified flux setpoint cannot be realized, although maximum cur-
rent is input.
— Motor data are incorrect
— Motor data and motor connection type (star/delta) do not match
— Motor has stalled because motor data are extremely inaccurate
— Current limit is too low for the motor (0.9 * P1238 * P1103 < P1136)
— Power section is too small
Remedy — Correct the motor data
— If required use a larger power section
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable

 

 

607 Current controller output limited
Cause The entered setpoint cannot be impressed in the motor, although the
maximum voltage has been entered. The cause could be that the motor
is not connected, or a phase is missing.
Remedy — Check the connecting cable, motor/drive converter (phase missing)
— Check the motor contactor
— DC link voltage present?
— Check the DC link busbar (check that the screws are tight)
— Uce monitoring function in the power section has responded
(RESET by powering off/powering on)
— Replace the power section or control module
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
608 Speed controller output limited
Cause The speed controller is at its limit for an inadmissibly long time (torque
and current limit). The permissible duration is defined in P1605, the
speed upper limit up to when the monitoring responds is defined in
P1606.
Synchronous motor:
In normal operation, the correct, optimized axis drive should never
reach its current limit — not even for extremely large speed changes
(changeover sequences from rapid traverse in the positive direction to
rapid traverse in the negative direction).
P1605 = 200 ms
P1606 = 8000 rev/min
Induction motor:
Acceleration and braking with the maximum torque/current are usual in
operation, only a stalled drive (0 speed) is monitored.
P1605 = 200 ms
P1606 = 30 rev/min
1. At the first commissioning, after the software has been replaced or
the software has been upgraded, after the parameters have been en-
tered the ”calculate motor data” or ”calculate controller data” function
was not executed. The drive then keeps the default values (for the val-
ues to be calculated this is zero) which can, under certain circum –
stances, result in this fault (P1605 and P1606 should be adapted to the
mechanical and dynamic capabilities of the axis).
2. An undesirable input of a high torque reduction via the analog inputs
or via PROFIBUS and the bus interface. For PROFIBUS and the bus
interface, this effect especially occurs when changing from the position-
ing mode to the speed setpoint input mode (check as to whether a
torque reduction is entered. Diagnostics using P1717, 0%: No torque,
100%: Full torque).
Remedy — Check connecting cable motor/converter (phase missing, exchanged)
— Check the motor contactor
— Check the torque reduction (P1717)
— DC link voltage present?
— Check the DC link voltage (check that the screws are tight)
— Unblock the motor
— Is the motor encoder connected?
— Check the motor encoder cable screen
— Is the motor grounded (PE connection)?
— Check the encoder pulse number (P1005)
— Does the encoder cable fit to the encoder type?
— Check the direction of rotation of the encoder tracks (e.g. toothed-
wheel encoder, P1011)
Adapt parameters P1605 and P1606 to the mechanical and dynamic
capabilities of the axis. Check whether a torque reduction has been
entered (diagnostics via P1717, 0%: no torque, 100%: full torque).
For linear motors:
— Check actual value inversion
— Check the reduction in the maximum motor current (P1105) and if
required increase the value
— Check the power cable connection
— For the parallel circuit configuration, are the motors correctly as-
signed and electrically connected?
— Uce monitoring function in the power section has responded (RESET
by powering off/powering on)
— Replace the power section or control module
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
609 Encoder limit frequency exceeded
Cause The speed actual value exceeds the encoder frequency.
— Incorrect encoder
— P1005 does not correspond to the no. of encoder pulses
— Encoder defective
— Motor cable defective or not properly attached
— Shield on motor encoder cable is not connected
— Defective control module
Remedy — Enter correct encoder data / replace encoder
— Check the encoder pulse number (P1005)
— Attach motor cable correctly or replace
— Connect the motor encoder cable screen
— Reduce the speed setpoint input (P1401)
— Replace control module
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable

 

 

610 Rotor position identification has failed
Cause if P1075=1 (technique based on saturation)
A rotor position could not be determined from the measurement signals
(motor current), as no significant saturation effects occurred.
Also refer to parameter P1734 for detailed diagnostics.
if P1075=3 (motion-based technique)
1. Current increase too low.
2. Maximum permissible duration exceeded.
3. No clear rotor position found.
Remedy if P1075=1
— Increase current via P1019
— Check armature inductance (P1116) and if required, increase
— Check the connecting cable, motor/drive converter (phase missing)
— Check the motor contactor
— DC link voltage present?
— Check the DC link busbar (check that the screws are tight)
— Uce monitoring function in the power section has responded
(RESET by powering off/powering on)
— Replace the power section or control module
if P1075=3
To 1.
— The motor is not correctly connected
— The motor power connection must be checked
To 2.
— Remove disturbing external forces (e.g. axis couplings which are not
released)
— Identification technique must remain stable (P1076 must be reduced)
— Use an encoder with higher resolution
— Improve the encoder mounting (it is not stiff enough)
To 3.
— Remove disturbing external forces (e.g. axis couplings which are not
released)
— The axis must be able to freely move (e.g. the motor rotor may not be
locked)
— Reduce the high axis friction (increase P1019)
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable

 

 

611 Illegal motion during rotor position identification
Cause During the rotor position identification (motor current measurement),
the motor rotated more than the value entered in P1020. The rotation
could be caused by having powered on with the motor already rotating,
or caused by the identification routine itself.
Remedy if P1075=1
— If the interchange was caused by the identification itself and if the
error occurs again, then reduce P1019 or increase P1020.
— Lock the motor rotor during the identification routine.
if P1075=3
— Increase the parameterized load mass (P1076)
— Check the maximum permissible motion (P1020) and if required,
increase
— Reduce the current, rotor position identification (P1019)
If the current and speed controller clock cycle have low values (62.5
microseconds), then it maybe necessary to increase P1019.
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
612 Illegal current during rotor position identification
Cause 1. Current was >= 1.2 * 1.05 * P1107 while rotor position identification
was active
2. Current was >= P1104 while rotor position identification was active
Remedy With the rotor position identification (P1011.12 and P1011.13) acti-
vated, if required, check and reduce P1019 (current, rotor position iden-
tification)
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
613 Shutdown limit, motor overtemperature exceeded.
Supplementary information \%X
Cause .. is specified in the additional information:
1 The motor temperature is sensed using a KTY temperature sensor.
a) The motor temperature has exceeded the temperature limit in
P1607.
b) The sensor or the cable is interrupted or has a short-circuit.
2. The motor temperature is sensed using a PTC temperature sensor.
b) The sensor or the cable has a short-circuit.
3. The thermal motor model has tripped because the permitted thermal
motor utilization in P1266 was exceeded.
Remedy — Avoid many acceleration and braking operations which follow one
another quickly.
— Motor overload?

 

— Check whether the motor output is sufficient for the drive, otherwise use a more powerful motor, possibly together with a higher-rating power section.

 

— Check the motor data. The current could be too high due to incorrect motor data.

 

— Temperature sensor monitoring.

 

 

  • Check whether the sensor type (KTY or PTC) is correctly set in P1609.

 

  • If the alarm occurs with the motor in the cold condition check whether

 

the sensor is short -circuited or the cable is interrupted.
— Check the motor fan.
— Check the motor encoder cable.
— Motor encoder defective?
— Check and possibly reduce P1230 or P1235.
The motor temperature monitoring can be disabled with P1601 bit 13 =
1.
For linear motors:
— Check the parameters for the motor temperature monitoring
P1602 (alarm threshold, motor overtemperature) = 120 degrees C
P1603 (timer, motor temperature alarm) = 240 s
P1607 (shutdown limit, motor temperature) = 155 degrees C
P1608 (fixed temperature) = 0 degrees C
P1608 = 0 —-> Temperature sensing active
P1608 > 0 —-> Fixed temperature active
— If the temperature monitoring is exclusively realized using an external
PLC, a fixed temperature must be entered into P1608
(e. g. 80 degrees C). This disables the drive temperature monitoring.
— Check the parameters for the thermal motor model
P1265 (thermal motor model configuration)
P1268 (winding time constant)
P1288 (shutdown threshold, thermal motor model)
— Check the power connector at the motor
— Check the connection of the temperature sensor coupling cable at the
end of the power cable, approx. 580 Ohm (KTY) or 100 Ohm (PTC)
must be able to be measured at 20 Degrees C
— If the measuring system connector is withdrawn (X411 for 611U or
MOT ENCODR for POSMO) is approx. 580 Ohm (KTY) or 100 Ohm
(PTC) measured between PIN 13 (611U) or 20 (POSMO) and PIN 25
(611U) or 21 (POSMO)at 20 Degree C?
— Check the measuring system connector at the drive (X411 or
MOT ENCODR) to ensure that it is correctly inserted
— For drives connected in parallel, both KTY temperature sensors may
not be directly connected. In this case an appropriate evaluation unit,
e.g. SME-92 or SME-94 should be used for 2 drives.
— If the temperature switch and temperature sensor are connected in
series, the temperature sensor (NC contact) may have responded, or
the temperature switch is defective
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
614 Delayed shutdown for motor overtemp. (P1602 /
P1603). Supplementary info. \%X
Cause .. is specified in the additional information:
1 The motor temperature is sensed using a KTY temperature sensor.
a) The motor temperature has exceeded the temperature limit, motor
overtemperature P1602 for a longer period of time than that permitted
in P1603.
b) The sensor or the cable is interrupted or has a short-circuit.
2. The motor temperature is sensed using a PTC temperature sensor.

 

 

  1. The motor temperature has exceeded the PTC-specific switching temperature for a time longer than that permitted in P1603.

 

  1. The sensor or the cable has a short-circuit.

 

  1. The thermal motor model has tripped because the permitted thermal motor utilization alarm threshold P1269 was exceeded for a time longer than permitted in P1603.

 

Remedy — Avoid many acceleration and braking operations which follow one
another quickly.
— Motor overload?
— Check whether the motor output is sufficient for the drive, otherwise
use a more powerful motor, possibly together with a higher-rating
power section.
— Check the motor data. The current could be too high due to incorrect
motor data.
— Check the thermal motor utilization alarm threshold P1269.
— Temperature sensor monitoring.
— Check whether the sensor type (KTY or PTC) is correctly set in
P1609.
— If the alarm occurs with the motor in the cold condition check whether
the sensor is short -circuited or the cable is interrupted.
— Check the motor fan.
— Check the motor encoder cable.
— Motor encoder defective?
— Check and possibly reduce P1230 or P1235.
The motor temperature monitoring can be disabled with P1601 bit 14 =
1.
For linear motors:
— Check the parameters for the motor temperature monitoring
P1602 (alarm threshold, motor overtemperature) = 120 degrees C
P1603 (timer, motor temperature alarm) = 240 s
P1607 (shutdown limit, motor temperature) = 155 degrees C

P1608 (fixed temperature) = 0 degrees C

 

P1608 = 0 temperature sensing active

 

P1608 > 0 fixed temperature active

 

— If the temperature monitoring is exclusively realized using an external PLC, a fixed temperature must be entered into P1608

 

(e. g. 80 degrees C). This disables the drive temperature monitoring. — Check the parameters for the thermal motor model

 

P1265 (thermal motor model configuration)

 

P1268 (winding time constant)

 

P1288 (shutdown threshold, thermal motor model) — Check the power connector at the motor

 

— Check the connection of the temperature sensor coupling cable at the end of the power cable, approx. 580 Ohm (KTY) or 100 Ohm (PTC) must be able to be measured at 20 Degrees C

 

— If the measuring system connector is withdrawn (X411 for 611U or MOT ENCODR for POSMO) is approx. 580 Ohm (KTY) or 100 Ohm (PTC) measured between PIN 13 (611U) or 20 (POSMO) and PIN 25 (611U) or 21 (POSMO)at 20 Degree C?

 

— Check the measuring system connector at the drive (X411 or MOT ENCODR) to ensure that it is correctly inserted

 

— For drives connected in parallel, both KTY temperature sensors may not be directly connected. In this case an appropriate evaluation unit, e.g. SME-92 or SME-94 should be used for 2 drives.

 

 

  • If the temperature switch and temperature sensor are connected in series, the temperature sensor (NC contact) may have responded, or

 

the temperature switch is defective
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
615 DM encoder limiting frequency exceeded
Cause The speed actual value of the direct measuring system exceeds the
permissible encoder limiting frequency.
— Incorrect encoder
— P1007 does not coincide with the encoder pulse number
— Encoder defective
— Defective encoder cable or not correctly retained
— Encoder cable shield is not connected
— Defective control module
Remedy — Enter correct encoder data / replace encoder
— Check encoder pulse number (P1007)
— Correctly retain encoder cable / replace
— Connect encoder cable shield
— Reduce speed setpoint input
— Replace control module
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
616 DC link undervoltage
Cause The infeed has gone into a fault condition and the DC link voltage has
fallen below the permissible lower limit P1162.
Remedy — Check whether the line supply voltage is available
— Check whether the pulsed resistor is overloaded
— Switch-off/switch-on infeed
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable
617 DC link overvoltage
Cause The DC link voltage has exceeded the permissible upper limit P1163.
Dynamic energy management has been activated using P1155, bit 0
and the DC link voltage has exceeded the ”Maximum DC link voltage
dyn. energy management” P1153 (from SW 13.1).
Remedy — Check whether the line supply voltage is available
— Reduce load duty cycle
— Check P1163
— If P1155 bit 0 is activated, increase P1153 or deactivate P1155 bit 0
(from SW 13.1)
Acknowledgement RESET FAULT MEMORY
Stop response parameterizable

 

 

680 Illegal motor code number
Cause A motor code was entered in P1102 for which no data is available.
Remedy — Commission the system again and enter the correct motor code
number (P1102).
— The ”SimoCom U” parameterizing and start -up tool includes motors
that are still not known in this particular drive version. Either upgrade
the drive version or enter the motor as non-listed motor.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
681 Illegal power section code number
Cause A power section code was entered in P1106, for which no data is avail-
able.
Remedy — Enter the correct power unit code in P1106.
— For power modules with automatic identification, upgrade firmware.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
682 Illegal encoder code number in P\%u
Cause An encoder code was entered in P1006 or P1036, for which there is no
data.
The direct measuring system (P0250/P0879.12) is activated, although
an encoder was not specified in P1036.
Remedy Enter the correct encoder code or the code for third-party encoders
(99) in P1006 or P1036.
De-activate direct measuring system (P0250/P0879.12).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

683 Calculate controller data was unsuccessful at first
start-up (\%d)
Cause An error occurred at the first start-up with ”calculate controller data”.
Under fault conditions, the parameters for the current controller, flux
controller and speed controller could not be optimally assigned.
Remedy Read-out the detailed cause of the error from P1080 and remove the
cause.
Then initiate ”calculate controller data” again with P1080 = 1. Repeat
this operation, until no error is displayed in P1080. Then save in the
FEPROM and execute a POWER ON-RESET.
Error coding in the supplementary info and P1080:
–15 magnetizing reactance (P1141) = 0
–16 leakage reactance (P1139 / P1140) = 0
–17 rated motor frequency (P1134) = 0
–18 rotor resistance (P1138) = 0
–19 motor moment of inertia (P1117) = 0
–21 threshold speed for field weakening (P1142) = 0
–22 motor standstill current (P1118) = 0
–23 The ratio between the maximum motor current (P1104) and the
motor stall current (P1118) is greater than the maximum value for the
torque limit (P1230) and the power limit (P1235).
–24 The ratio between the rated motor frequency (P1134) and the rated
motor speed (P1400) is inadmissible (pole pair number).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
703 Invalid current controller cycle
Cause An illegal value was entered in P1000.
Remedy Enter a valid value in P1000.
Permissible values for P1000 are:
2 (62.5  s) for single-axis positioning or for speed setpoint input
4 (125  s) in each operating mode
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
704 Invalid speed controller cycle
Cause An illegal value was entered into P1001.
Remedy Enter a valid value in P1001.
Permissible values for P1001 are 2 (62.5  s), 4 (125  s), 8 (250  s), 16
(500  s).
Setting 2 (62.5  s) is only permissible for single-axis operation.
Further, P1001 must be >= P1000.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

705 Invalid position controller cycle
Cause The monitoring function identified a position controller cycle (P1009)
outside the permissible limits.
Remedy Enter a valid value in P1009.
Permissible values for P1009 lie between 32 (1 ms) and 128 (4ms).
Further, the position control cycle must be a integral multiple of the
speed control cycle.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
706 Invalid interpolation cycle
Cause The monitoring function has identified an interpolation clock cycle
(P1010) that is outside the permissible limits or an illegal ratio between
the interpolation clock cycle and the position controller clock cycle
(P1009).
Remedy Enter a valid value in P1010 or correct P1009.
Permissible values for P1010 lie between 128 (4ms) and 640 (20ms)
or, only for the 1-axis version, also 64 (2ms) if P1009 is also 64 (2ms).
Further, the interpolation cycle must be an integral multiple of the posi-
tion controller cycle.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
708 Axial deviations in current controller cycle
Cause On a 2-axis module, the current controller cycle is different for both
axes.
Remedy Check P1000 and set the input values the same for both drives.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
709 Axial deviations in speed controller cycle
Cause On a 2-axis module, the speed controller cycle is different for both
axes.
Remedy Check P1001 and set the input values the same for both drives.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
710 Axial deviations in position controller or interpolation
cycle
Cause For a 2-axis module, the position controller clock cycle (P1009) or the
interpolation clock cycle (P1010) is different for the two axes.
Remedy Check P1009 / P1010 and set the input values for both drives the
same.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

716 Invalid torque constant
Cause The ratio between the rated torque and rated current (torque constant
[Nm/A]) in P1113 is incorrect (less than/equal to zero) or the ratio
P1113 / P1112 is greater than 70.
Remedy Enter the valid torque/current ratio for the motor used in P1113 or enter
a permissible ratio of P1113 / P1112.
Third-party motor:
The torque constant should be determined from the motor data sheet.
Siemens motor:
The torque constant is defined by the motor code (P1102).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
718 BERO shutdown threshold exceeded
Cause BERO speed actual value is greater than the shutdown threshold spe-
cified in P1468 (the motor is prevented from accelerating in an uncon-
trolled fashion) or for a calculated speed > 1200 rpm, BERO pulses are
no longer received (e.g. the cable is interrupted)
Remedy Check the parameterization of the induction motor
Check BERO or BERO cable, BERO pulse length
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
719 Motor not parameterized for delta operation
Cause When the star-delta changeover is activated using P1013, the motor is
not parameterized for delta operation (motor 2).
Remedy Check and enter the parameters for delta operation (motor 2).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
720 Invalid maximum motor speed
Cause Due to the high maximum motor speed in P1401 and the speed con-
troller cycle in P1001, high partial speeds can occur which can result in
a format overflow.
Remedy Check P1401 and P1001 and correct.
The drive software is designed for large reserve margins, so that the
displayed alarm can only occur as a result of a parameterizing error.
Example:
For a speed controller cycle time of 125  s, a motor speed of 480 000
RPM can still be processed correctly!
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

721 Spindle speed too high
Cause As a result of the high spindle speed and the interpolation clock cycle
(P1010), the modulo value can no longer be correctly taken into ac-
count. The alarm is initiated, if jerky equalization motion occurs — e.g.
due to incorrect parameter values.
Remedy Shorten the interpolation clock cycle.
If possible, increase the modulo range of the rotary axis (P0242).
Calculating the spindle speed limit [RPM] = 7 / IPO clock cycle[ms] x
60 x 1000 (for the modulo range, 360 degrees = 1 spindle revolution)
Example:
IPO clock cycle = 4 ms, for max. 7 revolutions (up to 7 x modulo range)
— a maximum spindle speed of 105000 RPM is obtained per IPO clock
cycle.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
722 Changeover speed/velocity too low
Cause For the selected setting of P1466, the induced voltage is too low in the
lower speed range in order to be able to reliably guarantee sensorless
operation. The induced voltage must be at least 40 Volt (phase-to-
phase, RMS) at the particular speed.
Remedy The following should be ensured:
Induction motor : P1466 >= 150 RPM
Rotary synchronous motor: P1466 > 40000 / P1114
Linear motor: P1466 > 1386 / P1114
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
723 Axial deviations in STS configuration
Cause On a 2-axis module, the gating unit configuration (P1003) is different
for the two gating units.
Remedy Check P1003 and set the bits for the two module axes the same (do
not change the standard setting, this represents the optimum configura-
tion).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

724 Invalid motor pole pair number
Cause Synchronous motors:
— The pole pair number in P1112 is zero or negative.
— Encoder with CD track (P1027.6 = 0): The pole pair number in P1112
is greater than 6.
— Encoder without CD track or with Hall sensors (P1027.6 = 1): The
motor pole pair number is dependent on the encoder pulse number
(max. 4096 for P1005 >= 32768).
Induction motors:
— An invalid pole pair number was determined from P1134 and P1400.
Motor with resolver:
— The maximum motor pole pair number for the modules
6SN1118–*NK01–0AA0 or 6SN1118–*NJ01–0AA0 is 64, otherwise 4 or
6.
Remedy Synchronous motors:
— Check P1112, P1027.6 and P1014.
Induction motors:
— Determine and correctly enter rated speed and/or rated frequency.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
725 Invalid encoder pulse number
Cause The encoder pulse number of the motor measuring system (P1005) is
set to zero.
Remedy Harmonize the encoder pulse number of the motor measuring system
in P1005 to the encoder used. The indirect motor measuring system
must always be configured for synchronous and induction motors (ex-
ception: Induction motor operation).
Standard setting: 2 048 increments/revolution
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
726 Invalid voltage constant
Cause The voltage constant of the motor in P1114 is set to zero.
Remedy Determine the voltage constant of the motor used, and enter in P1114.
The voltage constant is measured as induced voltage (EMF) under no-
load conditions at n = 1 000 RPM as RMS valued at the motor termi-
nals (phase to phase).
Third-party motor:
The voltage constant should be determined from a motor data sheet.
Siemens motor:
The voltage constant is determined from the motor code (P1102).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

727 Invalid combination of power section and synchron-
ous motor
Cause The power module has not been released for synchronous motors.
Remedy — Check configuring
— Use a valid power section
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
728 Torque/current adaptation factor too high
Cause The adaptation factor between the setpoint torque and the torque gen-
erating current (Iq) in the speed controller is too high.
Remedy Check P1103, P1107 and P1113 and if required, enter correct values.
Third-party motor:
The values should be determined from a motor data sheet.
Siemens motor:
The values are determined from the motor code (P1102).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
729 Invalid motor stall current
Cause The motor stall current (P1118) is less than or equal to zero.
Remedy Determine the stall current of the motor used and enter in P1118.
Third-party motor:
The stall current should be determined from a motor data sheet.
Siemens motor:
The stall current is determined from the motor code (P1102).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
731 Invalid rated output
Cause The rated motor output (P1130) of the motor is less than or equal to
zero.
Remedy Determine the rated motor output of the motor used and enter in
P1130.
Third-party motor:
The rated motor output should be determined from a motor data sheet.
Siemens motor:
The rated motor output is determined from the motor code (P1102).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

732 Invalid rated speed
Cause The rated motor speed (P1400) of the motor is less than or equal to
zero.
Remedy Determine the rated speed of the motor being used and enter into
P1400.
Third-party motor:
The rated motor speed should be determined from a motor data sheet.
Siemens motor:
The rated motor speed is determined from the motor code (P1102).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
738 Incorrect mode, analog input for the equalization con-
troller
Cause If the equalization controller is parameterized with P1490 = 1 –> then
P0612 must be parameterized with the value 3
Remedy — P0612=3 or
— P1490 not equal to 1
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
739 Incorrect axis number, equalization controller
Cause If the equalization controller is parameterized with P1490 = 2 –> two
active axes must be available on the module.
Remedy — P1490 equal to 1 (coupling via analog terminals)
or
— Activate the 2nd axis
or
— Use a 2-axis module
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
742 V/f operation: Drive frequency, motor \%d not permissi-
ble
Cause In V/f operation, only drive converter frequencies of 4 or 8 kHz are per-
missible.
Remedy Change P1100 or cancel V/f operation (P1014).
When operating with several motors/motor data sets, also set
P2100/P3100/P4100 to 4 or 8 kHz.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

743 Function is not possible using this control board
Cause ”
Remedy ”
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
744 Motor changeover only permissible for the closed-loop
speed controlled mode
Cause Motor changeover (P1013) may only be activated in the closed-loop
speed controlled mode (P0700 = 1).
Remedy — Inhibit motor changeover (P1013 = 0)
— Change over into the closed-loop speed controlled mode (P0700 = 1)
Acknowledgement POWER ON
Stop response STOP I
745 New EnDat encoder
Cause For a direct measuring system with EnDat it was identified that the se-
rial number does not correspond with that saved — i.e. the serial num-
ber of the encoder has still not been saved.
Remedy Save parameters, then power on
Acknowledgement POWER ON
Stop response parameterizable
749 Speed measuring range is not sufficient
Cause The maximum speed which can be achieved with speed feedback can-
not be measured using the module.
Remedy — Parameterize the encoder type corresponding to the type of motor
and the control module.
— Synchronous motor: P1147 * resolver pole pair number must be less
than the limiting frequency of the control module (12 bit: 25402 RPM;
14 bit: 6350 RPM).
— Induction motor : min ( P1146, P1465 ) * resolver pole pair number
must be less than the limiting frequency of the control module (12 bit:
25402 RPM; 14 bit: 6350 RPM).
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

750 Speed monitoring BERO incorrectly configured
Cause -for the BERO speed monitoring function, parameter P0890 ”Activate
angular encoder/encoder interface” must be set to 4 (input for TTL en-
coder),
— Parameter P0894 ”Angular encoder input signal form” must be set
to 1 (pulse/direction signal”,
— Parameter P1465 ”Changeover speed MSD/IM” set to 0,
— Parameter P1006 ”IM encoder code number” or P1036 ”DM encoder
code number” must be set to 98 (without encoder).
Remedy Adapt the angular encoder interface, change over to operation without
encoder, correct the changeover speed.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
751 Speed controller gain too high
Cause P gain, speed controller for the lower speed range (P1407) and the up-
per speed range (P1408) were selected to be too high.
In AM (induction motor) operation:
The P gain of the speed controller (P1451) is too high.
Remedy Reduce the P gain of the speed controller.
Only optimized with the adaption disabled (P1413 = 0). The P gain
(P1407) is then effective over the complete speed range. After the opti-
mum setting has been found, adaption can be re-enabled (P1413 = 1)
and the P gain optimized for the upper speed range (P1408).
In AM (induction motor) operation:
For the speed controller, enter a lower value for the P gain (P1451).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
753 Current, rotor position identification less than the min.
value
Cause A current was parameterized in P1019 (current, rotor position identifica-
tion) which is less than the minimum value permissible for the motor.
Remedy Enter a current in P1019, which is not less than the permissible mini-
mum value for the motor (40% for third-party synchronous linear
motor). It may be necessary to use a larger power module.
If permissible for the motor used, suppress the fault by setting P1012,
bit 5.
Caution:
For motors with weak saturation effects (e.g. 1FN3 linear motors), as a
result of the low identification current, orientation may be erroneous,
thus resulting in uncontrolled motion.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

756 Invalid speed hysteresis of the current setpoint
smoothing
Cause The hysteresis of the speed for the current setpoint smoothing (P1246)
may not be greater than the threshold speed of the hysteresis (P1245),
as otherwise a ”negative” lower speed would be obtained.
Remedy P1246 (standard value: 50 [RPM]) must be entered lower than the
threshold for the speeddependent setpoint smoothing (P1245, standard
value: 4 000 [RPM]).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
757 PZD config.: illegal frame no. in P0922
Cause The frame number set in P0922 is illegal or impermissible for the oper-
ating mode currently selected via P0700.
Remedy Check P0922 and enter valid value.
Acknowledgement POWER ON
Stop response STOP II
758 Setpoint source incorrectly parameterized. Supplemen-
tary info \%u
Cause The selected setpoint source in P0891 is invalid.
1  Internal coupling not possible for POSMO or single-axis module
2  Internal coupling not possible for drive A
3  Coupling via PROFIBUS-DP or the bus interface selected, but the
matching option module is not inserted
Remedy Check P891 and enter a valid value.
Acknowledgement POWER ON
Stop response STOP II

 

 

759 Encoder/motor types do not match
Cause A linear motor was selected, and no linear scale configured
(P1027.4 = 0).
A rotating motor was selected and a linear scale configured
(P1027.4 = 1).
A resolver has been selected the pole pair number (P1018) of which is
illegal. A pole pair number =1 or the pole pair number of the motor
(P1112) is admissible.
The maximum speed (P1146) cannot be measured with the resolver.
The required resolution ( 1011[2]=1 or 1030[2]=1, resolver evaluation )
cannot be set with this module.
For this setting, either 6SN1118–*NK01–0AA0 or
6SN1118–*NJ01–0AA0 is required.
Remedy — Parameterize the encoder type corresponding to the type of motor
and the control module.
— Use the required (6SN1118–*NK01–0AA0 or 6SN1118–*NJ01–0AA0 )
control module.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
760 Pole pair width/scale graduations cannot be repre-
sented internally
Cause For linear motors, the equivalent (internal) pole pair number and (inter-
nal) encoder pulse number are calculated from the pole pair width and
grid division. In this case, the encoder pulse number must be an integer
multiple of one or x pole pair widths. This error message is output if the
pole pair width/grid division * x (up to x=4096) is not an integer multiple
or if an internal encoder pulse number which was calculated is too high.
A result with a tolerance of +/– 0.001 absolute is interpreted to be an
integer.
Remedy Long travel paths:
A linear measuring system with an encoder mark number that is an in-
tegral divisor of x* pole pair widths should be used.
Short travel paths:
For short travel, only a low error can accumulate which has hardly any
effect on the maximum achievable force and on the temperature rise, if
the encoder pulse number fits with a deviation of more than +/–0.001 in
the pole pair width. We then recommend that the pole pair width is
slightly changed.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

761 P0892 cannot be used with this measuring system
Cause The following settings are permitted (Order No.[MLFB] 6SN1118–…. ):
Incremental measuring systems ( 7 bit ) with sin/cos 1 Vpp without En-
Dat interface (..*NH00– 0AA*, ..*NH10–0AA*) : 0
Incremental measuring systems ( 7 bits ) with sin/cos 1 Vpp with EnDat
interface (..*NH00–0AA*, ..*NH10 –0AA*) : 0,1,2,3
Incremental measuring systems ( 11 bit ) with sin/cos 1 Vpp
(..*NH01– 0AA*, .. *NH11–0AA*) : 0,1,2,3,4
resolver ( 12 bit ) (..*NK00–0AA0 or ..*NJ00–0AA0) : 0,1,2,3
Resolver ( 12 bit ) (..*NK01–0AA0 or ..*NJ01–0AA0) with 12-bit resolu-
tion ( 1011[2]=0 or 1030[2]=0 ) : 0,1,2,3,4,5
Resolver ( 14 bit ) (..*NK01–0AA0 or ..*NJ01–0AA0) with 14 bit resolu-
tion ( 1011[2]=1 or 1030[2]=1 ) : –2,–1,0,1,2,3
Remedy Set P0892 (factor, angular encoder pulse number/encoder pulse num-
ber) to a valid value.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
762 P0893 cannot be used with this measuring system
Cause For incremental measuring systems with sin/cos 1 Vpp without EnDat
interface and for linear measuring systems with sin/cos 1 Vpp with En-
Dat interface, a zero pulse offset cannot be set via P0893.
Remedy Set P0893 (angular encoder zero pulse offset) to 0.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
764 Multiple assignment of terminal A or B (P0890)
Cause When selecting 3 in P0890, from drive A or B (setpoint at terminal A
and actual value at terminal B), it was identified, that terminal A or B
were already being used by another drive. Thus, this configuration is
not possible.
Remedy Check the configuration of terminals A and B in P0890 and eliminate
multiple assignments of both drives.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
765 P0890 and P0891 configure both setpoint inputs
Cause An actual value coupling is switched-in for drive B (P0891 = 1). At the
same time, for the same drive, terminal A or B was parameterized as
position setpoint input (P0890 = 2 or 3).
Remedy Check the configuration of terminals A and B in P0890, compare with
P0891 and eliminate multiple setpoint sources.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

766 Blocking frequency > Shannon frequency
Cause The bandstop frequency of a speed setpoint filter is greater than the
Shannon sampling frequency from the sampling theorem.
Remedy The bandstop frequency for P1514, filter 1 or P1517 for filter 2 must be
less than the inverse value of two speed controller clock cycles 1/ (2 *
P1001 * 31.25 microseconds).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
767 Natural frequency > Shannon frequency
Cause The natural frequency of a speed setpoint filter is greater than the
Shannon sampling frequency from the sampling theorem.
Remedy The natural frequency of a speed setpoint filter must be lower than the
reciprocal of two speed controller cycles.
Speed setpoint filter 1:
P1520 * 0.01 * P1514 < 1 / (2 * P1001 * 31.25 microseconds)
Speed setpoint filter 2:
P1521 * 0.01 * P1517 < 1 / (2 * P1001 * 31.25 microseconds)
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
768 Numerator bandwidth > twice the blocking frequency
Cause The numerator bandwidth of a current or speed setpoint filter is greater
than twice the blocking frequency.
This alarm is only generated for the general bandstop, if the following is
valid:
Speed setpoint filter 1: P1516 > 2 * P1514 or P1520 <> 100.0
Speed setpoint filter 2: P1519 > 0.0 or P1521 <> 100.0
Current setpoint filter 1: P1212 > 0.0
Current setpoint filter 2: P1215 > 0.0
Current setpoint filter 3: P1218 > 0.0
Current setpoint filter 4: P1221 > 0.0
Remedy The numerator bandwidth must be less than twice the bandstop fre-
quency.
Current setpoint filter 1: P1212 <= 2 * P1210
Current setpoint filter 2: P1215 <= 2 * P1213
Current setpoint filter 3: P1218 <= 2 * P1216
Current setpoint filter 4: P1221 <= 2 * P1219
Speed setpoint filter 1: P1516 <= 2 * P1514
Speed setpoint filter 2: P1519 <= 2 * P1517
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

769 Denominator bandwidth > twice the natural frequency
Cause The denominator bandwidth of a current or speed setpoint filter is
greater than twice the natural frequency.
This alarm is only generated for the general bandstop, if the following is
valid:
Speed setpoint filter 1: P1516 > 2 * P1514 or P1520 <> 100.0
Speed setpoint filter 2: P1519 > 0.0 or P1521 <> 100.0
Current setpoint filter 1: P1212 > 0.0
Current setpoint filter 2: P1215 > 0.0
Current setpoint filter 3: P1218 > 0.0
Current setpoint filter 4: P1221 > 0.0
Remedy The denominator bandwidth of a current or speed setpoint filter must
be less than twice the natural frequency.
Speed setpoint filter 1: P1515 <= 2 * P1514 * 0.01 * P1520
Speed setpoint filter 2: P1518 <= 2 * P1517 * 0.01 * P1521
Current setpoint filter 1: P1211 <= 2 * P1210
Current setpoint filter 2: P1214 <= 2 * P1213
Current setpoint filter 3: P1217 <= 2 * P1216
Current setpoint filter 4: P1220 <= 2 * P1219
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
770 Format error
Cause The calculated bandstop filter coefficients cannot be represented in the
internal format.
Remedy Change filter setting.
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
771 Induction motor oper.: drive converter frequency
motor \%d not permissible
Cause In induction motor operation (selected by P1465 < P1146), drive con-
verter frequencies of 4 or 8 kHz are permissible.
Remedy — Change P1100
— Cancel induction motor operation (P1465 > P1146)
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
772 Induction motor oper.: speed controller gain, motor
\%d too high
Cause The P gain of the speed controller (P1451) is too high.
Remedy For the speed controller, enter a lower value for the P gain (P1451).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

773 Not permissible to active analog input
Cause For this particular hardware version, it is not permissible to activate the
analog input.
Remedy — Set P0607 to 0 and P0612 to 0 or
— Use the ”SIMODRIVE 611 universal” control module.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
774 Induction motor oper.: changeover speed motor \%d
not permissible
Cause For mixed operation (with / without encoder) P1465 > 0, only closed-
loop controlled induction motor operation is permissible (P1466 <=
P1465).
Remedy Eliminate error by selecting pure induction motor operation (P1465 = 0)
or by canceling induction motor open-loop controlled operation (P1465
> P1466).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
775 SSI encoder incorrectly parameterized. Supplementary
info \%u
Cause Incorrect parameterization of the SSI absolute value encoder.
Supplementary info = 0x1, 0x11 (indirect, direct measuring system):
—-> The single-turn resolution cannot be 0.
Supplementary info = 0x2, 0x12 (indirect, direct measuring system):
—-> The number of parameterized bits is greater than the telegram
length.
Supplementary info = 0x3, 0x13 (indirect, direct measuring system):
—-> For linear encoders, it is not possible to have multi-turn resolution.
Remedy For supplementary info 1 or 11:
Check P1022 and P1032
For supplementary info 2 or 12:
Check P1021, P1022, P1027.12 and P1027.14 with respect to P1028
and check P1031, P1032, P1037.12 and P1037.14 with respect to
P1041
For supplementary info 3 or 13:
Check P1021 and P1031
Acknowledgement POWER ON
Stop response STOP I

 

 

776 TTL encoder not possible for older basic module
Cause For an old basic module, which does not support TTL encoders, a TTL
encoder was selected as motor measuring system.
Remedy Use a new basic module or incremental measuring system with sin/cos
1 Vpp.
Acknowledgement POWER ON
Stop response STOP I
777 Current for the rotor position identification too high
Cause A current was parameterized in P1019, which is greater than the cur-
rent which is permissible for the motor and the power section used.
Remedy Reduce the current via P1019.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
778 Impermissible converter frequency for rotor position ID
Cause When selecting the rotor position identification (P1019), drive converter
frequencies (P1100) of 4 or 8 kHz are permissible.
Remedy Change the drive converter frequency or cancel the rotor position iden-
tification.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
779 Motor moment of inertia, motor \%d invalid
Cause The motor moment of inertia (P1117) is incorrect (less than/equal to
zero).
Remedy Enter the valid motor moment of inertia for the motor used, in P1117.
Third-party motor:
The motor moment of inertia should be determined from a motor data
sheet.
Siemens motor:
The characteristic motor data should be determined from the motor
code (P1102).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

780 No-load current, motor > rated motor current (motor
\%d)
Cause The motor no-load current (P1136) has been parameterized greater
than the rated motor current (P1103).
Remedy Enter the valid currents for the motor used in P1136 and P1103.
Third-party motor:
The required currents should be determined using a motor data sheet.
Siemens motor:
The currents are determined using the motor code (P1102).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
781 No-load current, motor \%d > rated power section cur-
rent
Cause The motor no-load current (P1136) has been set to higher values than
the rated power section current.
before SW 2.4 the following is valid: Rated power section current =
P1111
from SW 2.4 the following is valid: Rated power section current = P1111
* P1099
Remedy — Enter the valid current for the motor used in P1136.
Third-party motor:
The required currents should be determined using a motor data sheet.
Siemens motor:
The currents are determined using the motor code (P1102).
— Reduce the power section pulse frequency P1100.
— Use a higher-rating power section (re-commission).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
782 Reactance motor \%d invalid
Cause The stator leakage reactance (P1139), the rotor leakage reactance
(P1140) or the magnetizing reactance (P1141) of the motor is incorrect
(less than/equal to zer0).
Remedy Determine the stator, rotor leakage reactance and magnetizing reac-
tance of the motor being used and enter into P1139, P1140 and P1141.
Third-party motor:
The values should be determined from a motor data sheet.
Siemens motor:
The values are determined from the motor code (P1102).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

783 Rotor resistance, motor \%d invalid
Cause The rotor resistance (P1138, cold) of the motor is zero or there was a
format overflow for an internal conversion.
Remedy The following parameters can have incorrect values:
P1001 (speed controller cycle)
P1134 (rated motor frequency)
P1138 (rotor resistance)
P1139 (leakage stator reactance)
P1140 (leakage rotor reactance)
P1141 (magnetizing field reactance)
Check the parameter, and if required, correct using the motor data
sheet.
The following condition must be fulfilled:
16 * P1001 * 0.00003125 * P1138 * 2PI * P1134 / (P1140 + P1141) < 1
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
784 No-load voltage, motor \%d invalid
Cause Error in no-load voltage P1135:
— P1135 <= 0 or
— P1135 > P1132 or
— P1135 * P1142 / P1400 + Vser.react. > 450V.
With Vser.react. = 0.181 * P1136 * P1142 * P1119
Remedy Determine the no-load voltage of the motor being used and enter into
P1135.
Third-party motor:
The following parameters may have incorrect values:
P1119 (inductance of the series reactor)
P1132 (rated motor voltage)
P1135 (no-load motor voltage)
P1400 (rated motor speed)
P1142 (threshold speed for field weakening)
P1136 (no-load motor current)
Check parameters and if required correct using a motor data sheet.
Siemens motor:
The no-load voltage is determined from the motor code (P1102).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

785 No-load current, motor \%d invalid
Cause The no-load current (P1136) of the motor (ARM) is incorrect (less than/
equal to zero).
Remedy Determine the no-load current of the motor (ARM) being used and en-
ter into P1136.
Third-party motor:
The no-load current should be determined from a motor data sheet.
Siemens motor:
The no-load current is determined from the motor code (P1102).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
786 Field-weakening speed, motor \%d invalid
Cause The threshold speed for field weakening for induction motors (P1142) is
incorrect (less than/equal to zero).
Remedy Determine the speed at which field weakening starts for the motor
being used and enter into P1142.
Third-party motor:
The field weakening speed should be determined from a motor data
sheet.
Siemens motor:
The field weakening speed is determined from the motor code (P1102).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
787 Induction motor oper.: feedforward control gain motor
\%d cannot be displayed
Cause The feedforward control gain for induction motors cannot be repre-
sented in the internal numerical format if the motor moment of inertia
and rated motor torque were unfavorably selected.
Remedy Operation without encoder:
Reduce the encoder pulse number (P1005), as this is used in the inter-
nal numerical format.
Operation with encoder:
Reduce the speed controller cycle (P1001).
Acknowledgement RESET FAULT MEMORY
Stop response STOP II (SRM, SLM) STOP I (ARM)
788 P0891 for drive B only
Cause An actual-value link has been activated (P0891 = 1) for drive A. The
hardware does not permit this setting.
Remedy For drive A, set P0891 to the value 0.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

789 Setpoint transfer SimoCom U ==> drive interrupted
Cause The setpoint transfer from SimoCom U to the drive was interrupted, i.e.
there is no longer an online connection. The Master Control was re-
turned to the drive.
Communication between the two communication partners was faulty.
While moving the drive using SimoCom U, other functions were car-
ried-out on the PG/PC (e.g. online help was opened, a file was opened)
so that from SimoCom U the drive can only be irregularly supplied with
data.
Remedy — Check whether SimoCom U is still operating correctly, if required, re-
start
— Check whether the communication connection is OK, if required, re-
place the connecting cable
— When in the online mode, do not select any time-intensive functions
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
790 Illegal operating mode. Supplementary info: \%u
Cause The selected operating mode (P0700) is not permitted for this module
or axis.
Supplementary info = 0x1:
Operating mode ==0 selected on the 1st axis
Supplementary info = 0x2:
”Positioing” operating mode selected for the Nset control module
Supplementary info = 0x3:
Operating mode is not possible with this firmware release
Supplementary info = 0x4:
”External position reference value” operating mode no longer possible.
Remedy For supplementary info 1:
Select valid operating mode (P0700 > 0)
For supplementary info 2:
Select Nset operating mode or use a positioning module.
For supplementary info 3:
Use a firmware release which supports this operating mode.
For supplementary info 4:
Select ”Positioning” operating mode.
Acknowledgement POWER ON
Stop response STOP I
791 TTL encoder interface incorrectly parameterized
Cause The TTL encoder interface may only be parameterized as follows for
this particular hardware version:
Drive A: P0890 = 0 or 4, 0: Interface inactive, 4: TTL encoder input
Drive B: P0890 = 0
Remedy Set P0890 to permissible value.
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

792 Direct measuring system incorrectly parameterized.
Supplementary info: \%u
Cause It is not permitted to parameterize the direct measuring system.
Supplementary info = 0x1:
A direct measuring system cannot be used using this board.
Supplementary info = 0x2:
The direct measuring system cannot be simultaneously operated with
drive B.
Supplementary info = 0x3:
The direct measuring system is active and drive A is set for encoder-
less operation (P1027 bit 5 = 1).
Remedy For supplementary info 1:
Use the required board.
For supplementary info 2:
— De-activate the direct measuring system for drive A (P0250/P0879.12
= 0)
or
— Switch drive B inactive (P0700 = 0)
For supplementary info 3:
— De-activate the direct measuring system for drive A (P0250/P0879.12
= 0)
or
— Commission the motor measuring system for drive A
Acknowledgement POWER ON
Stop response STOP I
793 Angular encoder signal waveform different for drive A
and B
Cause The input signal waveform for the angular encoder interface must be
set the same for the drives.
Remedy Check P0894 for both drives and set the same
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
794 P0890 = 3 not permitted for drive B
Cause This angular encoder interface setting is not permitted for drive B.
Remedy Check P0890 for drive B and set to a permissible value
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)

 

 

795 Ang. encoder, pos. ref. value normalization factor too
large. Suppl. info: \%u
Cause The position reference value normalization for the angular encoder in-
terface is not permissible.
Supplementary info
= 1 —-> Condition P0401 * P0895 < 8388608 violated
= 2 —-> Condition P0402 * P0896 < 8388608 violated
Remedy Check parameterization via P0401, P0402, P0895 and P0896. It may
be possible to achieve the conditions above by shortening the numera-
tor P0401 * P0895 with the denominator P0402 * P0896.
Acknowledgement POWER ON
Stop response STOP II
797 Error in center frequency measurement
Cause The speed was too high while measuring the center frequency (adjust-
ing the current actual value sensing). The center frequency is automati-
cally measured when ramping-up or when the pulses are inhibited.
Remedy Check the encoder cable.
Power up the drive converter if the motor runs at a reduced speed.
Acknowledgement POWER ON
Stop response STOP I
798 Measured value memory active
Cause The measured-value memory was active during power-up.
Remedy Run up again.
Acknowledgement POWER ON
Stop response STOP I
799 FEPROM backup and HW Reset required
Cause Parameters were re- calculated. Parameters must be saved and the
module run up again after this new calculation.
Remedy The newly calculated data should be saved in the FEPROM. The new
parameters become effective the next time that the module runs up!
Acknowledgement POWER ON
Stop response STOP II (SRM, SLM) STOP I (ARM)
800 Minus hardware limit switch
Cause A 1/0 edge was identified at the ”Minus hardware limit switch” input sig-
nal.
Remedy — In the pos mode: Return the drive to the traversing range using jog
key 1 or 2.
— In the n-set mode: Enter a setpoint that opposes the approach direc-
tion.
Acknowledgement not required
Stop response STOP VII

 

 

801 Plus hardware limit switch
Cause A 1/0 edge was identified at the ”Plus hardware limit switch” input sig-
nal.
Remedy — In the pos mode: Return the drive to the traversing range using jog
key 1 or 2.
— In the n-set mode: Enter a setpoint that opposes the approach direc-
tion.
Acknowledgement not required
Stop response STOP VII
802 Drive rotates in response to angular encoder output
parameters
Cause The drive was not stationary as the zero pulse offset was programmed
on the angular encoder interface. Low speeds are not critical, but the
inaccuracy of the zero pulse position increases in proportion to speed.
Remedy Ensure that the drive is at a standstill, or take into account a higher in-
accuracy of the zero pulse.
Acknowledgement not required
Stop response STOP VII
804 Controller enable or on/off 1(edge) or on/off 2/3 miss-
ing
Cause When starting a traversing block, the controller enable has not been
set, or the controller enable is missing during a traversing program
when re-starting the axis from standstill.
Controller enable missing, i.e. one of the following signals missing:
— PROFIBUS control signals (STW1.0: ON / OFF 1 (signal edge),
STW1.1: OC / OFF2, STW1.2: OC / OFF 3, STW1.3: Enable inverter /
pulse inhibit) and the appropriate signals of the bus interface
— PC enable (SimoCom U)
— Terminal 64
— Terminal 65.x
Remedy Set the missing signal, and re-start the traversing block or enter a sig-
nal edge via PROFIBUS.
Acknowledgement not required
Stop response STOP VII

 

 

805 Pulse enable missing
Cause When starting a traversing block, the pulse enable is not set, or the
pulse enable is missing during a traversing program when re-starting
the axis from standstill.
Pulse enable missing, i.e. one of the following signals missing:
— PROFIBUS control signals (STW1.1: OC / OFF 2, STW1.3: Enable
inverter / pulse inhibit) or the appropriate signals of the bus interface
— Terminal 48 (NE module)
— Terminal NS1/NS2 (NE module)
— Terminal 63 (NE module)
— Terminal 663 (control module)
Remedy Set the missing enable signal and then re-start the traversing block.
Acknowledgement not required
Stop response STOP VII
806 OC/reject traversing task missing
Cause When starting a traversing block, the ”operating condition / reject tra-
versing task” input signal is not set.
Remedy Set the ”operating condition / reject traversing task” input signal and
then re-start the traversing block.
Acknowledgement not required
Stop response STOP VII
807 OC/intermediate stop missing
Cause When starting a traversing block the ”operating condition / intermediate
stop” input signal is not set.
Remedy Set the ”operating condition / intermediate stop” input signal and then
re-start the traversing block.
Acknowledgement not required
Stop response STOP VII
808 Reference point not set
Cause When starting a traversing block, a reference point is not set.
Remedy Execute referencing or set a reference point using the ”set reference
point” input signal.
Acknowledgement not required
Stop response STOP VII
809 Parking axis selected
Cause When starting a traversing block or when starting referencing, the
”parking axis” function is selected.
Remedy Cancel the ”parking axis” function and then re-start the required func-
tion.
Acknowledgement not required
Stop response STOP VII

 

 

810 Velocity in the block \%n with override = 0
Cause The velocity programmed in this block was calculated with the actual
override and a value of 0 was obtained.
The velocity is set to the lowest unit.
Remedy Increase override.
Acknowledgement not required
Stop response STOP VII
811 Absolute value memory, alarm threshold
Cause Not enough absolute value memory space.
Remedy — Power-down the drive and power-up again
— POWER-ON RESET
Acknowledgement not required
Stop response STOP VII
814 Motor temperature, pre-alarm
Cause 1. The motor temperature is sensed using a temperature sensor
(KTY84 or PTC) and evaluated in the drive. This alarm is output if the
motor temperature reaches the alarm threshold, motor overtemperature
(P1602 for KTY or the PTC-specific switching temperature for PTC).
2. The thermal motor model has reached the thermal motor utilization
alarm threshold P1269.
Remedy — Avoid many acceleration and braking operations which follow one
another quickly.
— Check whether the motor output is sufficient for the drive, otherwise
use a more powerful motor, possibly together with a higher-rating
power section.
— Check the motor data. It is possible that the motor current is too high
as a result of incorrect motor data.
— Check the thermal motor utilization alarm threshold P1269.
— Temperature sensor monitoring.
— Check the motor fan.
Acknowledgement not required
Stop response STOP VII

 

 

815 Power module temperature, pre-alarm
Cause The power unit heatsink temperature is sensed using a thermosensor
located on the main heatsink. If the overtemperature condition remains,
then the drive shuts down after approx. 20 s.
Remedy Improve the drive module cooling, e.g. using:
— Higher airflow in the switching cabinet, possibly cool the ambient air
of the drive modules
— Avoid many acceleration and braking operations which follow quickly
one after the other
— Check that the power section for the axis/spindle is adequate,
otherwise use a higher-rating module
— Ambient temperature too high (refer to the Planning Guide)
— Permissible installation altitude exceeded (refer to the
Planning Guide)
— Pulse frequency too high (refer to the Planning Guide)
— Check fan, if required, replace
— Maintain the minimum clearance above and below the power section
(refer to the Planning Guide)
Acknowledgement not required
Stop response STOP VII
816 Resolver sensing at its limit
Cause At run-up, the speed with an existing resolver evaluation was extremely
high. It is possible that this was not the actual speed, and that the re-
solver was not connected to the measuring circuit input.
Remedy Insert the measuring circuit connector and enter a reset.
Acknowledgement not required
Stop response STOP VII
820 Power module in i2t limiting
Cause The power module is being operated too long above the permissible
load limit.
Remedy — Avoid many acceleration and braking operations which follow quickly
one after the other
— Check that the power section for the axis/spindle is adequate, other-
wise use a higher-rating module
— Pulse frequency too high (refer to the Planning Guide)
— Check P1260 and P1261
Acknowledgement not required
Stop response STOP VII
824 Function generator faulted \%d
Cause An error has occurred when activating the function generator.
Remedy Read-out the detailed fault cause from P1800 and remove the cause.
Fault coding in supplementary info and P1800.
Acknowledgement not required
Stop response STOP VII

 

 

827 Fieldbus is not in the data exchange state
Cause The bus interface is still not in the data exchange state or data ex-
change was interrupted.
Causes:
— The master has not yet run up, or has not yet established a
connection to the slave.
— The bus addresses differ in the master configuring and slave
parameterization.
— The bus connection has been physically interrupted.
— The master is still in the clear condition.
— An illegal parameterization or configuration was received.
— A BUS address was assigned several times.
Remedy Master, check the assignment of bus addresses and bus connection.
Acknowledgement not required
Stop response STOP VII
828 Fieldbus is not in clock-cycle synchronism to the
master
Cause The bus interface is in the data exchange state and was selected using
the parameterizing telegram of the clock-cycle synchronous operation.
It was not possible to synchronize to the clock cycle specified by the
master and to the master sign of life.
Causes:
— The master does not send an equidistant global control frame al-
though clock synchronism has been selected via the bus configuration.
— The master uses a different equidistant DP clock cycle as was com-
municated to the slave in the parameterizing telegram.
— The master does not increment its sign-of-life in the configured time
grid Tmapc.
Remedy Check master application and bus configuration
Check the consistency between the clock cycle input for the slave con-
figuring and the clock cycle setting at the master.
If the master (e.g. SIMATIC S7) does not transfer a sign-of-life, the
sign-of-life evalution can also be suppressed using P0879 bit 8.
Acknowledgement not required
Stop response STOP VII

 

 

829 PROFIBUS: Illegal parameterization received. Reason:
\%u
Cause An illegal parameterizing frame was received via PROFIBUS. Cyclic
data transfer cannot start.
Reasons:
8 = The parameterizing telegram has an illegal length
9 = The length data in the equidistant block is illegal
10 = A block header has an unknown ID.
11 = The basis time Tbasedp is not permissible (not equal to 125  s).
12 = The DP clock cycle Tdp is not permissible (less than 1ms or
greater than 32ms).
13 = The time Tmapc is less than 1*Tdp or greater than 14*Tdp.
14 = The base time Tbaseio is not permissible (not equal to 125  s).
15 = Time Ti is greater than the DP clock cycle (Tdp).
16 = Time To is greater than the DP clock cycle (Tdp).
17 = For active Data Exchange, a new parameterization was received
with different contents.
18 = Clock cycle synchronous operation was selected without a
suitable option module having been activated (refer to P0875).
19 = IsoM_Req (state 3, bit 4) is requested in the DPV1 header without
there being an isochron block (ID 0x04).
20 = Fail_Safe (state 1, bit 6), IsoM_Req (state 3, bit 4) or
Prm_Structure (state 3, bit3) missing in the DPV1 header although
an isochron block (ID 0x04) is available.
21 = The time Tdx is greater than (To — 125us) or greater than
(Tdp — 250  s).
22 = The time Tpllw is greater than 1us.
23 = Slave- to-slave communication access target address and length
do not conform to word boundary.
24 = Maximum number (3 external + 1 internal) of slave-to-slave
communication links has been exceeded.
25 = Maximum number (8) of accesses per link has been exceeded.
26 = Unknown version ID in the slave-to-slave communications block.
27 = The maximum overall length of the filter table has been exceeded.
31 = The permitted maximum length of the parameterizing telegram for
the option module has been exceeded.
32 = The option module firmware does not support slave-to-slave
communications
Remedy Check the bus configuration at the master, and if required correct the
parameterization.
If required, insert (reason 18) a suitable option module and activate.
If required, (reason 31 or reason 32) upgrade the option module firm-
ware to a version greater than or equal to 04.01.
Acknowledgement not required
Stop response STOP VII

 

 

830 PROFIBUS: Illegal configuration received. Reason: \%u
Cause An illegal configuration frame was received via PROFIBUS. Cyclic data
transfer cannot start.
Reasons:
1 = In the master, more axes are configured than are physically
present in the power module.
2 = The number of axes configured in the master is not equal to the
number axes for which the PROFIBUS-DP option module is
actively switched via P0875. Note: Even if axis B is de-activated
(passivated), communications with axis B are not automatically
de-activated.
3 = Configuration incomplete (too short) for one of the PPL types
(only for vor P875 = 2).
4 = No PPO type detected (only for P875 = 2).
5 = Length calculation different between firmware and option module.
6 = For active data exchange, a new configuration was received with
different length.
7 = Configuration contained unknown S7 ID.
19 = More PZD’s have been configured than the maximum permissible.
20 = The configurtion contains an unknown special character
(only axis separators are permitted).
22 = Target offset of slave-to-slave communications access exceeds
the maximum number of PZDs
28 = Number of slave-to-slave communication IDs differs from the
number of accesses in the parameterizing telegram.
29 = Setpoint PZDs are not uniformly supplied by the master or slave
(drive) publisher.
30 = The permitted maximum length of the configuration telegram for
the option module has been exceeded.
Remedy Check the bus configuring at the master and if required correct.
If required, using P875, activate the option module PROFIBUS-DP,
which are previously configured in the PROFIBUS Master for the num-
ber of axes involved.
Acknowledgement not required
Stop response STOP VII

 

 

831 PROFIBUS is not in the data transfer condition
Cause The PROFIBUS is not in a data transfer status (data exchange) or data
transfer was interrupted.
Causes:
— The master has not yet run up, or has not yet established a connec-
tion to the slave.
— The bus addresses differ in the master configuring and slave parame-
terization.
— The bus connection has been physically interrupted.
— The master is still in the clear condition.
— An illegal parameterization or configuration was received.
— A PROFIBUS address was assigned several times.
Remedy Master, check the assignment of bus addresses and bus connection.
Acknowledgement not required
Stop response STOP VII
832 PROFIBUS not clock-synchronous with the master
Cause The PROFIBUS is in a data transfer status (data exchange) and has
been selected via the parameterizing frame of synchronous operation.
It could not yet be synchronized to the clock preset by the master resp.
to the master sign-of-life.
Causes:
— The master does not send an equidistant global control frame al-
though clock synchronism has been selected via the bus configuration.
— The master uses a different equidistant DP clock cycle as was com-
municated to the slave in the parameterizing telegram.
— The master increments its sign-of-life (STW2 Bits 12–15) not in the
configured time frame Tmapc.
Remedy Check master application and bus configuration
Check the consistency between the clock cycle input for the slave con-
figuring and the clock cycle setting at the master.
If the master (e.g. SIMATIC S7) does not transfer a sign-of-life, the
sign-of-life evalution can also be suppressed using P0879 bit 8.
Acknowledgement not required
Stop response STOP VII

 

 

833 PROFIBUS: No connection to the publisher \%u
Cause Cyclic data transfer between this slave and a slave-to-slave commu-
nications publisher was still not started or was interrupted.
Examples:
— Bus connection interrupted
— Publisher failure
— Master runs up again
— The response monitoring (Watchdog) for this slave was de-activated
via the parameterizing telegram (SetPrm)
(Diagnostics: P1783:1 bit 3 = 0).
Supplementary info: PROFIBUS address of the publisher
Remedy Check the publisher and bus connections to the publisher, to the
master and between the master and publisher.
if the watchdog is de-activated, activate the response monitoring for
this slave via Drive ES.
Acknowledgement not required
Stop response STOP VII
840 Teach-in for running traversing program
Cause Teach-in was requested during a running traversing program.
Remedy Exit the traversing program and re-request teach-in.
Acknowledgement not required
Stop response STOP VII
841 Teach-in for relative block
Cause The traversing block as ”teach in block” is relative instead of absolute.
Remedy Change the traversing block mode ”teach in block” from relative to ab-
solute.
Acknowledgement not required
Stop response STOP VII
842 Teach-in for a relative standard block
Cause The traversing block as ”teach in standard set”, is relative instead of
absolute.
Remedy Change the traversing block mode ”teach in standard block” from rela-
tive to absolute.
Acknowledgement not required
Stop response STOP VII

 

 

843 Search velocity too high
Cause The search velocity for spindle positioning is too high for the selected
maximum deceleration.
Remedy Reduce the search speed P0082:256 or increase the maximum decel-
eration P0104.
Acknowledgement not required
Stop response STOP VII
845 Jogging not effective for active coupling
Cause Jogging is not possible while a coupling is closed.
Remedy Release the coupling and re-activate jogging.
Acknowledgement not required
Stop response STOP VII
849 PLUS software limit switch actuated
Cause For a block with the ENDLOS_POS command, the axis has actuated
the plus software limit switch (P0316) for absolute or relative position-
ing.
The behavior for software limit switch reached, can be set using
P0118.0.
Remedy — Move away in the negative direction, jogging.
— Move away in the negative direction using the traversing block.
Acknowledgement not required
Stop response STOP VII
850 MINUS software limit switch actuated
Cause For a block with the ENDLOS_NEG command, the axis has actuated
the minus software limit switch (P0315) for absolute or relative position-
ing
The behavior for software limit switch reached, can be set using
P0118.0.
Remedy — Move away in the positive direction, jogging.
— Move away in the positive direction using the traversing block.
Acknowledgement not required
Stop response STOP VII
864 Parameterization error in speed controller adaptation
Cause The upper adaption speed (P1412) was parameterized with a lower
value than the lower adaption speed (P1411).
Remedy P1412 must contain a higher value than P1411.
Acknowledgement not required
Stop response STOP VII

 

 

865 Invalid signal number
Cause The signal number for the analog output is not permissible.
An analog value can be output for diagnostic, service and optimization
tasks
Term. 75.x/15, 16.x/15, DAC1, DAC2
Remedy Enter valid signal number
(refer to the Description of Functions SIMODRIVE 611 universal)
Acknowledgement not required
Stop response STOP VII
866 Parameterizing error, current controller adaption
Cause For the current controller adaption, the upper current limit (P1181) was
parameterized with a lower value than the lower current limit (P1180).
Adaption is de-activated when the parameterizing error is output.
Remedy P1181 must contain a higher value than P1180.
Acknowledgement not required
Stop response STOP VII
867 Generator mode: Response voltage > shutdown
threshold
Cause The sum of the values in P1631 + P1632 is greater than the value in
P1633.
Remedy Boot module
Note:
P1630 to P1633 are internal Siemens parameters
Acknowledgement not required
Stop response STOP VII
868 Regenerative operation: shutdown threshold > re-
sponse threshold
Cause The input value for the shutdown threshold, regenerative operation
(P1633) is greater than (or equal to) the response threshold, DC link
voltage (P1630).
Remedy Boot module
Note:
P1630 and P1633 are internal Siemens parameters
Acknowledgement not required
Stop response STOP VII
869 Reference point coordinate limited to modulo range
Cause The reference point coordinate is internally limited to the modulo range.
Remedy Enter a value in P0160 which lies within the modulo range (P0242).
Acknowledgement not required
Stop response STOP VII

 

 

870 Jerk: jerk time is limited
Cause When calculating the jerk time T from the acceleration a and the jerk r,
the result was an excessively high jerk time, so that the time is limited
internally.
The following is valid: T = a/r, where
a: Acceleration (higher value from P0103 and P0104)
r: Jerk (P0107)
Remedy — Increase jerk (P0107)
— Reduce maximum acceleration (P0103) or maximum deceleration
(P0104)
Acknowledgement not required
Stop response STOP VII
871 Induction motor operation: drive converter frequency
motor not permissible
Cause In induction motor operation (selected by P1465 < P1146), drive con-
verter frequencies of 4 or 8 kHz are permissible.
Remedy — Change P1100
— Cancel induction motor operation (P1465 > P1146)
Acknowledgement not required
Stop response STOP VII
872 PARAMETERIZING ERROR: P gain, equalization con-
troller too high
Cause PARAMETERIZING ERROR: P gain, equalization controller does not fit
into the format.
Remedy — Change P1491
Acknowledgement not required
Stop response STOP VII
875 Axial deviations in fixed voltage
Cause For the axes of a drive module, an unequal fixed voltage (P1161) was
set.
As a fixed voltage <> 0 replaces the DC link voltage measured value,
but the DC link voltage is only measured once for all drives of a drive
module, the fixed voltage on all module axes must be equal, before it is
accepted.
Remedy Set the same fixed voltage (P1161) on all module axes.
Acknowledgement not required
Stop response STOP VII

 

 

876 Terminal function \%u in the actual mode illegal
Cause The function number, used as input terminal or distributed input
(P0888) may not be used in the actual mode.
Remedy Change P0700 (operating mode) or enter a suitable function number in
P0888 or P0660, P0661 etc.
Acknowledgement not required
Stop response STOP VII
877 Output function \%u not permissible in the actual oper-
ating mode
Cause The function number, used as output, may not be used in the actual
operating mode.
Remedy Change P0700 (operating mode) or enter a suitable function number in
P0680, P0681, etc.
Acknowledgement not required
Stop response STOP VII
878 Input I0.x not parameterized as equivalent zero mark
Cause When entering an external signal as equivalent zero mark (P0174 = 2)
input I0.x must be assigned the function ”equivalent zero mark” (Fct.
No.: 79).
if a direct measuring system is used, input I0.B must be assigned the
”equivalent zero mark” function (Fct. No.: 79).
Remedy — Motor measuring system: P0660 = 79
— Direct measuring system: P0672 = 79
Acknowledgement not required
Stop response STOP VII
879 Time constant deadtime, speed feedforward control
(P0205:\%u) too high
Cause P0205:8 may not be greater than two position controller clock cycles.
Higher values are internally limited.
Remedy Reduce P0205:8 to max. two position controller clock cycles (P1009).
Parameterize an addition delay via P0206:8.
Acknowledgement not required
Stop response STOP VII

 

 

881 PZD configuring: Signal number in P0915:\%u invalid
Cause An undefined or illegal signal number in the current operating mode
(P0700) was identified for the process data software.
P0915:1 is not equal to 50001 (STW1).
The process data for encoder 1 has been configured although encoder-
less operation is activated (P1011.5).
The process data for encoder 2 were configured although the direct
measuring system is not activated (P0879.12).
Remedy Correct P0915:17
Acknowledgement not required
Stop response STOP VII
882 PZD configuring: Double word signal number in
P0915:\%u invalid
Cause For signals with double words (length = 32 bits), the corresponding sig-
nal identifier must be configured twice for adjacent process data. The
following subparameter must therefore also be parameterized with the
same signal number.
Remedy Correct P0915:17
Acknowledgement not required
Stop response STOP VII
883 PZD configuring: Signal number in P0916:\%u invalid
Cause An undefined or illegal signal number in the current operating mode
(P0700) was identified for the process data software.
P0916:1 is not equal to 50002 (ZSW1).
The process data for encoder 1 has been configured although encoder-
less operation is activated (P1011.5).
The process data for encoder 2 were configured although the direct
measuring system is not activated (P0879.12).
Remedy Correct P0916:17
Acknowledgement not required
Stop response STOP VII
884 PZD configuring: Double word signal number in
P0916:\%u ivalid
Cause For signals with double words (length = 32 bits), the corresponding sig-
nal identifier must be configured twice for adjacent process data. The
following subparameter must therefore also be parameterized with the
same signal number.
Remedy Correct P0916:17
Acknowledgement not required
Stop response STOP VII

 

 

885 P1261 greater than 100.0 % not permissible
Cause P1261 greater than 100.0 % is not permissible for permanent-magnet
synchronous motors with field weakening (PE spindle, P1015 = 1). It is
internally limited to 100.0 %.
Remedy Set P1261 to max. 100.0 %.
Acknowledgement not required
Stop response STOP VII
886 Pre-tensioning torque greater than 16x rated torque
Cause The parameterized pre-tensioning torque (P1493) is greater than 16x
the standstill torque (SRM), rated motor torque (ARM) and standstill
force (SLM) of the motor.
Note: refer to the index entry ”Limits”
Remedy Reduce pre-tensioning torque (P1493)
Acknowledgement not required
Stop response STOP VII
889 Fixed endstop, axis has not reached the clamping
torque
Cause The axis has reached the fixed stop — however was not able to estab-
lish the programmed clamping torque
Remedy Check the parameters for the limits.
Acknowledgement not required
Stop response STOP VII
890 Acceleration — deceleration override incorrect
Cause The acceleratino override or the deceleration override is not in the
range from 1% to 100%.
if the value > 100%, then it is limited to 100%.
If the value <  1%, then limited to  1%.
The traversing block is not interrupted.
Remedy Check the programming of the acceleration override and deceleration
override.
Acknowledgement not required
Stop response STOP VII

 

 

891 PLUS software limit switch actuated coupled
Cause With the actual master drive velocity, this coupling axis will probably
reach or pass the PLUS software limit switch.
This warning is output if the coupled axis has fallen below 200% of the
braking travel up to the PLUS software limit switch.
Remedy Traverse the master drive so that this coupling axis goes into the per-
missible traversing range.
Acknowledgement not required
Stop response STOP VII
892 MINUS software limit switch actuated coupled
Cause With the actual master drive velocity, this coupling axis will probably
reach or pass the MINUS software limit switch.
This warning is output if the coupled axis has fallen below 200% of the
braking travel up to the MINUS software limit switch.
Remedy Traverse the master drive so that this coupling axis goes into the per-
missible traversing range.
Acknowledgement not required
Stop response STOP VII
893 Function 73 only effective at terminal I0.x
Cause The terminal function 73 ”Coupling on I0” is only effective at terminal
I0.x.
Remedy Assign terminal I0.x to function 73.
Acknowledgement not required
Stop response STOP VII
894 Inputs, optional TERMINAL module assigned twice
Cause The input terminals on the optional TERMINAL module can only be
used by one drive.
Remedy Check and correct P0676 (A) and P0676 (B).
Acknowledgement not required
Stop response STOP VII
895 Outputs, optional TERMINAL module assigned twice
Cause Only one drive can use the output terminals on the optional TERMINAL
module.
Remedy Check and correct P0696 (A) and P0696 (B).
Acknowledgement not required
Stop response STOP VII

 

Unidrive Sizing

Control Techniques UNI3405 Unidrive

Control Techniques, Manual, UNIDrive, , ,
The UNI3405 Unidrive has 4 essential Modes:

1. Open Loop mode (OL)

For use with standard AC induction motors. The UNI3405 applies power to the motor at frequencies varied by the user. The motor speed is a result of the output frequency of the drive and slip due to the mechanical load. The drive can improve the performance of the motor by applying slip compensation. The performance at low speed depends on whether V/f mode or open loop vector mode is selected.

V/f mode

The voltage applied to the motor is directly proportional to the frequency except at low speed where a voltage boost is provided which is set by the user. This mode should used for multi-motor applications. Typically 100% torque at 4Hz.

Open loop vector mode

The voltage applied to the motor is directly proportional to the frequency except at low speed where the drive uses motor parameters to apply the correct voltage to keep the flux constant under varying load conditions. Typically 100% torque at 1Hz.

2. Closed loop vector mode (VT)

For use with induction motors with a speed feedback device fitted. The UNI3405 directly controls the speed of the motor using the feedback device to ensure the rotor speed is exactly as demanded. Motor flux is accurately controlled at all times to provide full torque all the way down to zero speed. Typically 175% torque at 0rpm.

3. Servo (SV)

For use with permanent magnet brushless motors with a speed and position feedback device fitted. The Unidrive directly controls the speed of the motor using the feedback device to ensure the rotor speed is exactly as demanded. Flux control is not required because the motor is self excited by the permanent magnets which form part of the rotor. Absolute position information is required from the feedback device to ensure the output voltage is accurately matched to the back EMF of the motor. Typically 175% torque at 0rpm

4. Regen

For use as a regenerative front end for four quadrant operation. Regen operation allows bi-directional power flow to and from the AC supply. This provides far greater efficiency levels in applications which would otherwise dissipate large amounts of energy in the form of heat in a braking resistor. The harmonic content of the input current is negligible due to the sinusoidal nature of the waveform when compared to a conventional bridge rectifier or thyristor front end.

Unidrive Sizing Chart –
Unidrive Sizing
Unidrive Sizing
If you are interested in ordering a replacement Unidrive, please call 1-800-691-8511, or email sales@mrostock.com.

6SN1145-1BA02-0CA1: Emergency Stop Procedures

Manual, Siemens, Simodrive, , ,

Click Now to Visit Our 6SN1145-1BA02-0CA1 Product Page.

For all SIMODRIVE devices the basic principle of the safety–related circuit is the same. However, the different devices can have different terminal designations. The following circuit examples can be used, in an adapted form, for all SIMODRIVE infeeds and drives, including the 6SN1145-1BA02-0CA1. The specifications to prove the Performance Level can be kept. For reasons of transparency, in the following examples, only the safety–related terminals are connected. To move the drives, all of the necessary enable terminals must be supplied. In the following examples, power contactors with mirror contacts as well as contactor relays with positively–driven contacts are used. For reasons of simplicity, the mirror contacts of the power contactors are designated as standard as positively–driven contacts.

Continue reading 6SN1145-1BA02-0CA1: Emergency Stop Procedures →

140CPS11420 Manual Anthologies

Manual, Modicon, Schneider Electric, ,

140CPS11420: Manual Anthologies

Click now to visit our Modicon 140CPS11420 Product Page

There exists some important design differences between various models of Quantum power supplies that require careful consideration by the system designer in order to achieve maximum system performance. The principal difference lies in the generation within the power supply of important backplane signals related to the health of the power supply and the status of the input power. All Quantum power supplies include on-board early power fail detection logic which is used to signal all other modules on the backplane that input power has failed. This signal is called POK (power OK) and is active high (i.e., when the signal is high, power is OK). There is both an internal (to the power supply) and an external (as seen by the backplane and all other modules) version of the POK signal. The internal POK signal is represented by the Pwr ok LED (light emitting diode) on the front panel of all power supplies. The system POK signal is generated so that there is sufficient time between the negative going edge of system POK (power has failed) and the actual interruption of power to the backplane. This early warning of power failure is necessary for the Quantum executive to perform an orderly system shutdown.

The 140CPS11420 is a Summable Power Supply. A summable power supply may be used as a standalone power supply without reservation in any Quantum system.

Continue reading 140CPS11420 Manual Anthologies →

6SN1145-1BA01-0BA1: Manual Anthologies

Manual, Siemens, Simodrive, Uncategorized, , ,
Click now to visit our Siemens 6SN1145-1BA01-0BA1 Product Page.

A SIMODRIVE drive group has a modular configuration comprising line filter, commutating reactor, line supply infeed module, drive modules as well as, when required: monitoring, pulsed resistor and capacitor module(s). Satisfactory operation is ensured only in conjunction with the components that are described in this Configuration Manual or published in the Catalog NC60 (Internet Mall) and with adherence to the required boundary/application conditions. Failure to observe this along with improper use and application conditions can void your certifications, conformity declarations or warranty claims. In order to avoid contamination, the modules should be installed in a control cabinet with degree of protection IP 54. Modules can also be arranged in several tiers one above the other or next to one another.

Continue reading 6SN1145-1BA01-0BA1: Manual Anthologies →